Manual TTulpe Smart Master DV060D (page 13 of 52) (English, German, Dutch, French)

782610

Zoom out

Zoom in

1/52

electricity tariff will be used. Such tariffs are available in some

countries that stimulate the electric power consumption in specified

time intervals to ensure even load of the energy distribution network in

the country. The thermoregulator will comply with the history of hot

water consumption for the last 7 days, in order to choose the maximum

water heating temperature in the period of ‘cheap’ tariff and when to do

so. For example, if the data analysis shows that on the same day of the

past week there was a greater hot water consumption, water will be

heated up to a higher temperature in the current night. In order to

provide sufficient quantity of hot water, water will be also heated during

the day but to the minimum usage temperature of 40оC. If on two or

more subsequent days the electricity consumption is sufficiently low,

the appliance will switch to the most economical water heating and

‚Reduced Power’ (7) will read on the screen. In order to use the ‘Night

Tariff’ priority the start times of both tariff must be current!

NOTE! Where the water heater is in ‘Smart Control’ mode, there is an

option to proceed to forced water heating up to the maximum

temperature (POWERFUL submode) by pressing and holding button

(XI) for more than 2 sec. (8) In this submode, the two heating elements

will operate irrespective of the status of the ‘Fast Heating’ switch in

‘System Settings’ menu. Forced water heating will turn off automatically

when the two heating tanks are heated up to the required temperature.

Then it is proceeded to the normal operation of ‘Smart Control’ mode.

ATTENTION! In order to activate ‘Smart Control’ mode you need to set

the system clock to correct time!

‘Self-learning’ mode (9)

Prior to turning ‘Smart Control’ mode on with ‘Consumption Schedule’

priority, the water heater must undergo a procedure for measurement and

recording the hot water consumption schedule, which is performed by

starting the ‘Self-learning’ mode. This procedure lasts for 7 full days in order

to cover all specific features of weekly consumption. As the controller starts

the seven-day cycle at 00:00 o’clock on the next day, on the day when this

mode is activated water will be only heated up to the required temperature

without analyzing the consumption. After the end of the self-learning

procedure, the appliance will automatically switch to ‘Smart Control’ mode

with ‘Consumption Schedule’ priority.

‘Timers’ mode (10)-(11)

It allows for user-control of the water heating algorithm by using

thermoregulator weekly timers. They can adjust the water heater turning on

and the maximum water heating temperature. Each of the seven timers

allows for the entry of one time interval, specific days of the week in which it

will be active, and the maximum water heating temperature during the

specified interval. To activate the mode you must set the system clock to

correct time and have a set and active timer. The thermoregulator will

display in the left field on the screen information on the maximum water

heating temperature and the maximum operation time at that temperature or

the turn-on time.

NOTE! While the water heater is in this mode, there is an option of forced

water heating to the maximum temperature (POWERFUL submode) by

pressing and holding button (XI) for more than 2 sec. (8) In this submode,

the two heating elements will operate irrespective of the status of ‘Fast

Hearing’ switch in ‘System Settings’ menu. Forced water heating will turn

off automatically when the two water tanks are heated up to the required

temperature. Then, it will be proceeded to normal mode operation.

‘Delayed Start’ mode (13)

When the water heater is in ‘Off’ mode, pressing and holding of button (XII)

for 3 seconds will allow you to enter the time at which the appliance will turn

off automatically. The time is set by increments of 10 minutes. Delayed start

may be up to 24 hours. When entering a ‘Delayed start’ setting mode, the

default time is the current time rounded up to 10 minutes, and by subsequent

pressing of ▲ or ▼ buttons time may be increased or decreased. If any of

▲ or ▼ buttons is held for more than 0.7 sec., the value will be

automatically increased or decreased with a rate of 4 units per second. In

activated ‘Delayed Start’ mode, the turn-off time will be shown in the middle

of the screen.

To adjust a preset time, press and hold (XII) button again.

‘Delayed Start’ mode is cancelled by pressing (I) button and switching to

another mode.

The subsequent pressing of (I) button can return the setting to ‘Standby’

mode.

ATTENTION! In case of power supply interruption, while ‘Delayed Start’

mode is active, the controller will save the delayed start time. If the time

set comes before power recovery, when the power is recovered, the

controller will remained switched off.

Protection modes

џProtection from freezing. When the water heater is in ‘Off’ mode or

heating is suppressed by a preset timer, if water temperature falls

below 3°C, the anti-freezing mode is activated, and the heating

element is switched on and on the top of the screen reads ‚Anti-

freezing’ mode. As temperature rise above 3°C, the protection mode is

deactivated.

џ‘Anti-Legionella’. This is a function to prevent from the growth of

certain bacteria in the water. If the ‘Anti-Legionella’ function is enabled

from ‘System Settings’ menu, ‚Anti-Legionella’ field, and water has not

been heated up to 70°C for more than 7 days, this function will be

activated to ensure that water in the water heater will be heated up to

70°C, then the function will automatically deactivated. This function

will be activated one hour after the beginning of the night-time

electricity tariff.

ATTENTION! If the water heater is disconnected from the power supply

network, this will not change the preset temperature and the operation

mode at the time of disconnection. For example, if the water heater was

in ‘Heating’ mode when it was disconnected, after connection it will be in

the same mode with the same preset temperature.

ATTENTION! In the event of brief power outage, the set system time and

‘Delayed start’ mode associated with countdown time will still be active.

The time they will be active is up to 25 hours, if the water heater was

connected for more than 4 minutes or up to 40 seconds, if it was not

connected for such period.

ADDITIONAL INFORMATION - FIG. 8

When the controller is in a main screen and (IX) button is pressed, 4 screens

with additional information are displayed.

First, the electricity meters (1) separately for both tariff are displayed, energy

saved and date and time of last reset. While this screen is displayed, if (IX)

button is held for 2 seconds, the meters will be reset and the reset date and

time will be recorded. The energy saved is a tentative indicator. In order to

calculate it, it is necessary to determine how much the electricity costs will

be reduced when using the electronic Smart control compared to the

conventional (mechanical) control of the same water heater.

WARNING! Losses in the domestic hot water system (DHW) will

increase with the increase in hot water temperature and with the

lengthening of the water pipe from the water heater to the hot water

consumer.

On screen (1) when pressing ▼ button you go to a screen showing

information on the status of WiFi module (modem) (2), if any.

The field are as follows:

џID – Unique identifier of each modem

џIP – IP address of the modem

џWiFi mode – Connection status:

џIdle – the modem has not yet connected to an Internet-enabled

WiFi router.

џAccess point – the modem is in ‘Access point’ mode and can take

the name and password of a local WiFi network to connect to it.

џAP Associated – The modem has connected to the router.

џInternet Access – There is an Internet connection.

џConnected – The modem has connected to the server of the

information system. This should be the normal operation condition.

џSnd/Rcv – Data packets sent / received through the Internet

On screen (2) when pressing ▼button you will see a screen showing

information on the versions of the thermoregulator and WiFi module (3), if

any.

When you subsequently press ▼button you go to the ‚System Information’

screen (4), which shows information on the operation of heating elements

(turned on or off) if the first (FT) and second (ST) water tank, which are inlet

and outlet, respectively. The water temperatures measured in both water

tanks are displayed here.

When you subsequently press‚ i‘ button you will see screens showing

diagrams of electricity consumed by hours (5). The controller stores such

information for the last 8 days. Pressing the ▲ or ▼ buttons will change

diagrams with the days for which data is available. Each diagram shows the

data it is referred to, the energy consumed by the water heater in the first

EN EN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of TTulpe Smart Master DV060D in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1.2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

TTulpe Smart Master DV060D Manual

Product: