484625

Trumatic E 2400 E Manual

19
Zoom out
Zoom in
Previous page
1/24
Next page
19
In order to avoid overheating, there must be at least one
air passage which is always open (swivel nozzle SCW 2).
Secure all duct connections with self-tapping screws. Fasten
ducts with clamps.
The warm air system is designed for each type of vehicle
individually, on a modular basis. There is an extensive acces-
sories program available (refer to brochure). Diagrams with
optimum installation suggestions for warm air systems can be
requested free of charge from the Truma Service Centre.
Circulating air return
The circulating air (U) is sucked back into the appliance, either
directly or via a duct piece VR 80 (80 mm diameter).
1. Direct intake: If the appliance is installed in a storage com-
partment or such, drill two holes measuring 75 mm in
diameter into it, or make a corresponding opening for the
circulating air return.
Do not obstruct the air passage to the appliance!
2. Circulating air outside the storage area can be drawn in via
a duct piece VR 80 (1) 80 mm diameter (max. 1 m in length)
and returned to the appliance. The storage compartment
can then be used to the full.
Remove protective grating from the connection fitting (3).
Insert duct piece (1) into the grating connection fitting and
fasten using the available screws. Attach swivel nozzle SCW 2
to the duct end (4).
Warm air supply and circulating air return
with outside assembly
Refer to installation variants fig. 3 + 4 (page 2).
The warm air supply and the circulating air return between ap-
pliance and vehicle is provided by means of flexible air ducts
LF 18 (83 mm diameter, 60 cm in length). The air ducts can
be shortened as required. A protective casing over the entire
heater system protects it against damage and weather condi-
tions and simultaneously serves as insulation.
Connection of the ducts to the appliance
Remove the two protective gratings from the appliance. Coat
the two pipe pieces LF 18 (1) and the rein-forced ends (2) with
plastic body sealant and insert in the opening of the appliance
(W + U). Secure with two self-tapping screws (3). The duct
connection must be correctly assembled, otherwise splash
water can enter the appliance!
Assembly of the ducts at leadthroughs
Drill two openings 73 mm diameter (W + U). Coat the con-
nection fittings (4) on the flange with plastic body sealant and
screw on, at opening (U) place the protective grating (5) in
between.
Cut the two duct pieces LF 18 (6) to the required length, if
necessary, coat on the inside with plastic body sealant and
slide onto the connection (4). Secure with worm drive hose
clip (7).
On the inside, screw on the connection fitting (8) over the
opening (W – can also be screwed together with the connec-
tion fitting on the out-side). With hollow double walls make
sure to seal the intermediate space.
Warm air distribution
Connect duct VR 80 (9) 80 mm diameter and se-cure with
self-tapping screw (10). The various parts for the duct branch-
ing can also be mounted on the connection fitting (8), for the
further routing of the ducts VR (72 mm diameter), ÜR (65 mm
diameter) or ZR 18 (49 mm diameter).
In order to prevent overheat-ing, at least one air passage
must always be kept open (swivel nozzle SCW 2). Secure
all duct connections with self-tapping screws. Fasten duct
with clamp.
The warm air system is designed for each type of vehicle indi-
vidually, on a modular basis. There is an extensive accessories
program available (refer to brochure). Diagrams with optimum
installation suggestions for warm air systems can be request-
ed free of charge from the Truma Service Centre.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trumatic E 2400 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trumatic E 2400 E in the language / languages: English, German as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trumatic E 2400 E

Trumatic E 2400 E User Manual - English, German - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info