489384
10
Zoom out
Zoom in
Previous page
1/40
Next page
10
If it is intended that both hot water connection nozzles
should be fitted, the venting valve (1) can also be con-
nected by means of a T-piece (fig. C: 5 – max. hose length
between connec tion nozzles and bleeding valve 40 cm).
Water connection
The Therme can be installed in already existing systems with a
single tap, as shown in fig. A, with a Truma mixing valve (part
no. 40020-00300 – not part of the scope of delivery) or as
shown in fig. B, with pre-selecting mixing tap(s).
All hose connections must be secured with hose clips
(also cold water)!
All connection fittings are designed for 10 mm hoses.
Using the hose clips SC (6; part no. 40712-01 – not
included in scope of delivery) it is possible to route the
water hoses on the hot air pipes, providing protection against
frost.
Clamp the hose clips under the clips of the hot air pipes.
They can also be used for fastening the water hoses to the
wall or floor.
Installation of the Truma mixing valve
The Truma mixing valve is equipped with a backflow preventer
towards the pump. Only possible with fittings with electrical
switch.
When using other pre-mixing valves, always observe the
respective instructions!
When using several single-tap fittings, a pre-mixing
valve must be installed for each one respectively!
Fig. A
Drill a hole with dia. 16 mm in the vicinity of the tap (15), on a
flat surface of the wash basin, sink or vertical wall in front of it
always higher than the actual Therme, vertically align mixing
valve using the two nuts and fasten in such a way that the up-
per nut (7) is approximately level with the end of the thread.
Mount control knob (8), screw on and turn to the left, up to
the stop.
Apply marking on the wash basin in such a way that this is
level with the end of the red symbol on the control knob of the
mixing valve.
Routing water pipes with the Truma mixing valve
Fig. A
Connect the mixing valve connection “from Therme” (9) to
one of the upper hot water connection nozzles.
Connect the mixing valve connection “to Therme” (10) to one
of the two lower cold water connection nozzles.
Connect mixing valve connection “pump” (11) and submergi-
ble pump (12).
Connect mixing valve connection “tap” (14) and water tap
(15).
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Truma Therme at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Truma Therme in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 0,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Truma Therme

Truma Therme User Manual - English, German, Dutch, Danish, French, Italian, Spanish - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info