Manual Truma Saphir comfort (page 16 of 54) (English, German, Dutch, Danish, French, Italian, Spanish)

489375

Zoom out

Zoom in

1/54

Installing the air conditioning system

when space is restricted

Preparation

Fig. B

Remove installation materials and remote control from stow-

age compartments (a and b) of the unit.

Fig. C

Open tension straps and remove the 4 fastening brackets.

1. Fig. C

Place installation template in stowage compartment and fix in

position. Mark mounting holes for the 4 side fastening brack-

ets (3) and the 2 front and rear retaining brackets (2 – leg must

be on the outside!).

2. Mark floor opening „LE” for the air supply, „LA” for the out-

going air and „KO” for the condensation drain.

3. Remove installation template and drill or cut out the „LE”,

„LA” and „KO” openings. Then seal the edges of the openings

in the floor of the vehicle with underfloor protection.

Before drilling, always check for underlying / concealed

cables, gas lines, frame sections and the like!

4. Screw down each of the 4 side fastening brackets (3) with

2 screws and each of the 2 retaining brackets (2 – leg must be

on the outside) with 3 screws.

The air conditioning unit must be attached at all sides

using the brackets provided in order to prevent unin-

tentional movement if vigorous movements occur (e.g. hard

braking).

5. Insert muff (11) for condensation drain (KO) from above.

6. Guide the two tension straps (4) through the 4 fastening

brackets (3) as shown in the illustration (lettering on tension

strap should be facing the floor). Insert air conditioning unit

in stowage compartment and secure with the two tension

straps (4). Ensure that the tension straps are positioned in

the recesses provided on the unit. Guide tension straps (4)

through the clasp (6) as shown in the illustration and tighten.

When installing the unit, please ensure that the

muff (11) of the condensation drain is located in

the recess in the floor of the vehicle. Otherwise there is

a risk of water penetrating the interior! In order to pro-

vide good air circulation, the openings in the bottom of

the unit and the floor must align exactly. Correct opera-

tion of the unit cannot be guaranteed unless this is the

case!

7. Seal muff (11) for condensation drain all round from below

using body sealant.

8. Attach the two floor grilles (5) for „LE” and „LA” to the floor

of the vehicle from below with suitable screws or clips (not

provided).

Cold air distribution and circulating air

return feed

Cold air distribution

A KR 65 Ø 65 mm (10) cold air duct with at least one outlet

must be connected to each of the three cold air emitters of

the unit (7, 8 and 9).

Slide the cold air ducts (10) into the cold air emitters of the

unit and route to the air outlet nozzles. Truma can supply a

muffler for installing in the cold air system (part no. 40040-

60100) as a accessory for reducing the amount of noise.

The SCW 2 swivel air outlet (black – part no. 39971-01 or

beige, part no. 39971-02), end piece EN-O (part no. 40171-07)

with lamella inset LA (part no. 40721-01/02/03/04/05) or the

RL rectangular air outlet (part no. 40280-01) with the ANH

connecting piece (part no. 40290-02) have proven to be suit-

able for emitting the cooled air into the interior of the vehicle.

Important notes

The cold air distribution system is individually designed for

each vehicle model using a modular principle. A wide range of

accessories is available for this purpose.

In order to achieve the best possible cooling power, we

recommend:

Route cold air pipes to air vents as short and straight as

possible.

The total accumulated length of cold air duct that may be

used is 15 m.

Connect the longest cold air pipe (max. 8 m) to the

right-hand cold air outlet (9), since this has the most air

throughput.

To prevent condensation in the cold air ducts, do not route

pipes anywhere near heat sources (e.g. power supplies or

behind the refrigerator).

Circulating air return

The circulating air is sucked in again by the device, either

through an additional air grille (1 – accessory, part no. 40040-

29200), for example in the wall of the stowage compartment,

or via a number of smaller apertures with a total surface area

of at least 300 cm².

Important note

To ensure trouble-free air exchange, the air infeed from the in-

terior of the vehicle to the installation location must be located

in the immediate vicinity of the device. If appropriate, covers

are to be fitted, in order to avoid the circulating air return be-

ing impeded by stowed objects.

If the equipment cannot be installed in close proximity,

Truma can provide a flexible air intake (part no. 40090-

59100) as an accessory.

–

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Truma Saphir comfort in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 7,43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Truma Saphir comfort Manual

Product: