590215

Truma Mover XT2 Manual

28
Zoom out
Zoom in
Previous page
1/96
Next page
28
If necessary, insert socket connector back into socket housing (i).
Screw socket housing (i) with rubber seal (h) to socket
holder (g) using 3 sheet metal screws (j). (Several positions
are possible by selecting the mounting holes on the socket
holder and rotating the rubber seal)
Lead cable loosely through the strain relief (k) and screw in
place with the 2 sheet metal screws. Depending on the instal-
lation situation, the cable can be led out of the socket holder
through one of the three recesses.
j
B 3.9 x 33
(3 x)
i
h
g
PT 4 x 10
k
Figure 36
Secure safety socket to the (plastic) shaft cover of the caravan
with 4 screws, nuts and washers.
M4 x 16
(4 x)
Washer 4.3
(4 x)
Nut M4 (4 x)
Figure 37
No holes must be drilled in the chassis.
Alternatively, the safety socket can be secured using the two
clips.
Figure 38
Route both wires to the control unit (shortening them if necess-
ary) and connect them to the connector block as shown in the
connecting diagram.
Re-check whether all cables are correctly connected, attached
using the provided clips and cannot chafe.
Function check
Check whether the battery is fully charged for operating the
Mover®XT / XT2.
Position the caravan on open, level ground and apply the
parking brake. The drive rollers must not be in contact with
the wheels and the corner jacks must be raised.
Connect the battery terminals to the battery. Check that all
cables are securely attached and not hot, and that there are
no signs of short circuits etc.
Plug the 13-pin plug / adapter into the safety socket.
Move slide switch on remote control to the “On” position.
This switches on the remote control, and green LED 4 flashes
until the control unit is ready for operation. If LED 4 does not
light up, check polarity and condition of batteries in remote
control.
Check that neither drive motor is running. With the remote
control switched on, operate the “slide control (C)”. Both drive
motors must rotate.
Engage drive rollers using remote control.
Ensure that there are no obstacles around the caravan and re-
lease the parking brake. Now check all functions several times
in accordance with the operating instructions.
Apply caravan parking brake. Disengage drive rollers and
move remote control slide switch to “Off” £ in order to switch
off the remote control and the Mover®XT / XT2. Re-check dis-
tance between drive rollers and tyres. Re-adjust if necessary.
The distance between the disengaged drive rollers and
the tyres is 20 mm.
Warnings
The installer or vehicle owner must apply the yellow sticker
with the warning information, which is enclosed with the ap-
pliance, in a location in the vehicle where it is clearly visible
to all users (e.g. the wardrobe door). Missing stickers can be
requested from Truma.
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Truma Mover XT2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Truma Mover XT2 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 11,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info