590215

Truma Mover XT2 Manual

19
Zoom out
Zoom in
Previous page
1/96
Next page
19
LED 4 green flashes if radio connection has not yet been
established after switching on the remote
control
lights up when remote control is ready for op-
eration and the data link is stable
flashes in combination with acoustic signal
– 10 seconds after switching on the remote control if the con-
trol unit is not yet ready for operation
– if the control unit has been switched off
– after 1 minute without pressing a button on the remote
control
– after a radio communication interruption
All LEDs “off” and no audio signal
System off
(check batteries in remote control if necessary)
Remote control battery change
Please only use leak-proof micro-batteries with a steel outer
casing, type LR 03, AAA, AM 4, MN 2400 (1.5 V).
When inserting new batteries, take care not to reverse the
positive and negative terminals.
Figure 3
Empty, used batteries can leak and damage the remote
control! Remove the batteries if the remote control is
not being used for a long period of time.
No warranty is given for damage caused by leaking
batteries.
Before disposing of a defective remote control, always re-
move the batteries and dispose of them correctly.
Manoeuvring the caravan
Follow the “Safety instructions” before using the
Mover®XT / XT2.
Apply parking brake if caravan is uncoupled.
Disconnect 13-pin plug / adapter from vehicle and plug into
safety socket of caravan.
For safety reasons, the Mover®XT / XT2 can only be op-
erated if the 13-pin plug / adapter of the caravan is
plugged into the safety socket.
In the event of a malfunction, the 13-pin plug / adapter
must not be removed from the safety socket until the
parking brake has been applied, since removing the plug dis-
ables the electronic safety functions.
Switch on the remote control – green LED 4 flashes until the
control unit is ready for operation. If the control unit is not
ready for operation, the remote control switches off after
about 10 seconds.
Press the two buttons (i) for engaging simultaneously, and en-
gaging will start after approx. 3 seconds (safety delay).
Use the position indicator to check that both drive rollers
are correctly engaged.
Before starting the Mover®XT / XT2, release the parking
brake.
Movement in all directions is possible using the control knob
and the slide control.
The Softstart / Softstop makes the caravan start to move
without jolting, and brakes it gently when stopping.
When the control knob or slide control are released, or if the
radio signal is interrupted or becomes too weak, the caravan
stops moving. Radio equipment and other Mover® remote
controls will not activate your Mover®.
After start-up, the Mover®XT / XT2 moves at a steady speed
(according to the setting on the slide control). Speed increases
slightly on downhill slopes and decreases on uphill slopes.
After manoeuvring, apply the parking brake first and then
disengage the drive rollers from the tyres.
Move slide switch on remote control to the “Off” position
toswitch the remote control off (the Mover®XT / XT2 switch-
es to standby mode).
The slide switch also acts as an “Emergency Stop”
switch.
Remove the plug / adapter from the safety socket after ma-
noeuvring, otherwise the control unit will automatically switch
off after 1 hour. The battery is discharged with a quiescent
current of approx. 80mA if the plug / adapter is in the socket.
Coupling to a towing vehicle
The Mover®XT / XT2 allows a caravan to be coupled to a
towing vehicle without jolting and with millimetric precision.
However, this requires care and a degree of practice.
Following the operating instructions, move the caravan close
to the towing vehicle (apply parking brake and engage gear).
In order to position the caravan precisely, operate the control
knob or slide control until the caravan's coupling is located
precisely over the ball coupling on the towing vehicle. Then
couple the caravan to the vehicle by lowering it at the support
wheel in the usual manner.
Prepare the caravan for towing in the usual way.
The caravan must not be towed with the drive rollers
engaged.
Maintenance
Keep drive elements clear of coarse road dirt. When cleaning
the caravan, spray the Mover®XT / XT2 with a water hose to
remove mud etc. Make sure that no stones, twigs etc. are
trapped in it. The control unit does not require servicing. The
remote control must be kept in a dry place.
Clean the Mover®XT / XT2 as described above every year (or
before overwintering). Do not park the caravan with the drive
rollers engaged.
To prevent the battery from becoming totally discharged dur-
ing long periods of inactivity it must be disconnected and
recharged before using again. Charge the caravan battery
before starting up.
It is extremely easy for you or your caravan dealer to perform
the checking and maintenance of your Mover®XT / XT2 dur-
ing the annual inspection of your caravan. If in doubt, please
contact Truma Service or one of our authorised service part-
ners (see www.truma.com).
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Truma Mover XT2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Truma Mover XT2 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 11,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info