484650

Truma Mover Mover H SE R Manual

21
Zoom out
Zoom in
Previous page
1/76
Next page
21
Safety socket connection with conventional
brake lights
(applies to 7-pin and 13-pin sockets!)
The fact that there are two conventional brake lights and
a third brake light with LED technology does not affect
this connection.
Route the provided 2-wire cable (10 m) with the wire-end fer-
rules through the socket holder (g) and the rubber sleeve (h).
Open cover and push socket connection out of socket housing (i).
Connect wire with longitudinal red stripe to pin 6 and black
wire to pin 3 (pin designation printed on connection and on
inside of cover).
Re-insert socket connection into socket housing (i).
Screw socket housing (i) to socket holder (g) using 3 sheet
metal screws (j). (Several alternative positions are available
by using the mounting holes in the socket holder and rotating
the rubber seal).
Loosely route cable through strain relief (k) and secure with
2 sheet metal screws. Depending on the installation situation,
the cable can be led out of the socket holder through one of
the three recesses.
j
B 3.9 x 33
(3 x)
i
h
Pin 3
Pin 6
g
PT 4 x 10
k
Secure safety socket to the
(plastic) shaft cover of the
caravan with 4 bolts, nuts and
washers.
No holes must be drilled
in the chassis.
M 4 x 16
(4 x)
Washer 4,3
(4 x)
Nut M 4 (4 x)
Alternatively, the safety socket
can be secured using the two
worm drive hose clamps.
Route wire connected to pin 6 (with red stripe) to control unit
(shorten if necessary), crimp on a flat plug and connect as
shown in the connecting diagram.
Route wire connected to pin 3 (black) to control unit (shorten
if necessary), crimp on a ring and screw to negative battery
terminal as shown in connecting diagram.
The connection to the control unit must be made in the
order – nut, battery negative terminal ring, nut, cable
pin 3 ring, nut.
Re-check whether all cables are correctly connected, attached
using the provided clips and cannot chafe.
Safety socket connection with LED brake lights
This connection must always be used if all brake lights
are of the LED variety! With two conventional brake
lights and a third brake light with LED technology, the connec-
tion is made as described in “Safety socket connection with
conventional brake lights”.
7-pin safety socket
Connect pin 3 of the caravan plug to the negative battery
terminal.
Connect pin 3 of the safety socket to the controller (with
one wire of the 2-wire cable).
13-pin safety socket
Connect pin 11 of the caravan plug to the negative battery
terminal.
Connect pin 11 of the safety socket to the controller (with
one wire of the 2-wire cable).
If it is not possible to make a connection using pin 11 (pin
missing, for example), use pin 3 as an alternative.
It must be ensured that ground connections pin 11
and pin 3 are not interconnected in an electrically
conductive manner at the trailer side!
Connecting diagram with LED brake lights
1
+
-
Safety
socket
Engagement
motors
Drive
motor
Drive-
motor
Battery
1
– + – +
– +
234
Caravan
plug
13-pin
3
11
8
1
2
97
5
4
6
10
1213
7-pin
3
4
6
7
1
5
2
11
3
8
1
2
97
5
4
6
10
1213
6
4
7
1
5
2
3
Safety
contact
Fuse
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Truma Mover Mover H SE R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Truma Mover Mover H SE R in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 9,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info