Manual Truma B 14 (page 6 of 24) (English, German, Dutch, Danish, French, Italian, Spanish)

489380

Zoom out

Zoom in

1/24

Boiler B 10 / B 14

Installation and repair are only to be carried out by an

expert. Always read and follow the operating instructions

carefully prior to starting any work!

Non-compliance with installation instructions or

incorrect installation can result in endangerment

of persons and property.

Approval

Declaration of conformity

The Truma water heater model has been tested and approved

through the DVGW and fulfils the EC gas appliance guidelines

(90/396/EEC) as well as the associated EC guidelines. The CE

Ident. Number is available for EU countries: CE-0085AP0038

EC Type Approval

e1 03 2604

Regulations

Guarantee claims, warranty claims and acceptance of liability

will be ruled out in the event of the following:

modifications to the unit (including accessories),

modifications to the exhaust duct and the cowl,

failure to use original Truma parts as replacement parts

and accessories,

failure to follow the installation and operating instructions.

It also becomes illegal to use the appliance, and in some

countries this even makes it illegal to use the vehicle.

In-vehicle installations must comply with the technical and

administrative regulations of the respective country of use

(e.g. EN 1949 for vehicles). The national regulations and rules

(e.g. DVGW work sheet G 607 in Germany) must be complied

with.

In other countries always observe the respectively valid

regulations.

More information on the regulations in the relevant destina-

tion countries can be requested from our foreign representa-

tives (see Truma Service Booklet or www.truma.com).

–

Choice of location

Always install the appliance in such a way that it is easily

accessible for service work at all times and can be easily re-

moved and installed.

Locate the heater in such a way that the cowl can be mounted

on the outside on a surface which is as straight and smooth

as possible.

This outside surface must be exposed to wind from all

directions and, if possible, there should be no trim strips

or covers in this area, mount heater on an appropriate base,

if necessary.

Fig. H

The wall cowl must be attached so that no tank supports or

tank ventilation openings are found within 500 mm (R). In ad-

dition, no air discharge apertures for the living area or window

openings may be located with 300 mm (R) of it.

When fitting the cowl within the marked area below or

next to a window that must be open, an electrical win-

dow switch (part no. 34000-85800) must be installed. The gas

unit must automatically switch itself off using the Truma auto-

matic shut-off facility if the window is opened (Accessories,

part no. 70020-00800).

Installation of the water heater

Position template for cowl opening on the inside of the wall.

A = bottom edge of heater

B = lateral edge of heater

Drill 4 holes (C) with 10 mm dia. through the wall. Drill hole (E)

with 15 mm dia. for condensation pipe (also possible from the

outside = F).

Position template on the outside of the wall. The markings (C)

must be above the through-holes. Saw cut-out section for

cowl (D) 92 x 168 mm.

If the distance between outside wall and heater is more than

35 mm you must use the cowl extension VBO 2 (part no.

70131-00) with an additional length of 50 mm. Saw out

100 x 176 mm along the dashed line.

If there are any cavities in the area of the cowl (fig. A: 1), pack

these with pieces of wood so as to be able to tighten the

screws.

Cut out trim strips or such on the vehicle or place supports

beneath them so as to make the cowl lie flat.

Place a support beneath the heater if the walls are sloping. An

angle of inclination of 10 degrees is not to be exceeded.

Fig. A

Insert heater with cowl body (3) through the cowl opening (1),

allow approx. 5 mm to project out of the wall. Mount sealing

frame (4 – the anti-torsion device ensures correct fitting!).

Pre-drill holes for the 6 fastening bolts (5).

Remove sealing frame (4) and coat with plastic sealant on the

side facing the vehicle – do not use silicone!

The sealing frame must be well sealed with respect to

the front sides and the cross bars of the cowl part (3) as

well as towards the outside wall!

Fasten sealing frame (4) to the cowl part using 4 selfcutting

screws (7 – torque 3.5 Nm).

Seal the gap between the hole (2) and the condensation

tube (10) with plastic sealant – do not use silicone!

Mount the grille (8). Press the entire cowl assembly onto the

vehicle wall and fasten with 6 screws (5).

Installation instructions

Symbols used

Symbol indicates a possible hazard.

Comment including information and tips.

Liquid gas storage water heater

(Special version B 10 EL, B 14 EL with additional electric

heating 230 V, 850 W)

Intended use

This appliance has been designed for the installation in cara-

vans, mobile homes and other vehicles. It is not approved for

installation in boats. Other forms of use are also possible fol-

lowing consultation with Truma.

Information regarding boats

For installation in boats Truma supplies the DVGW-tested boat

water heater.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Truma B 14 in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 2,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Truma B 14

Truma B 14 User Manual - English, German, Dutch, Danish, French, Italian, Spanish - 44 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Truma B 14 Manual

Product: