Manual Truma Aventa comfort (page 21 of 80) (English, German, Dutch, Danish, French, Italian, Spanish)

489376

Zoom out

Zoom in

1/80

Location selection

After installation of the air-conditioning system, any ex-

isting exhaust cowl nearby must extend at least 10 cm

over the air-conditioning system. The exhaust cowl must be

extended if necessary (pay attention to the heater manufactur-

er‘s information).

The vehicle roof (roof thicknesses from 25 to 110 mm) must

be level and smooth.

There are 3 installation options:

A new cut-out has to be made (350 x 380 mm).

Cut-out from an existing skylight (400 x 400 mm) without

sealing frame (accessories).

Cut-out from an existing skylight (400 x 400 mm) with seal-

ing frame (accessories) (Operating instructions are supplied

with the sealing frame.)

Please always take the following requirements into

account:

If at all possible, the unit should only be installed a little way

from the centre of the vehicle.

Check that installation will not be obstructed in any way.

There may be electrical cables running between the inside

and the outside of the roof. Disconnect all voltage sources

before starting work (all poles).

The maximum permitted roof load must not be exceeded

(see the vehicle manufacturer‘s specification).

Check the internal installation location for obstructions.

A wooden reinforcement frame must be fitted around

the cut-out in the roof between the upper and lower roof

surface (min. 25 mm). It may be necessary to remove the

insulation.

Installation in a 400 x 400 cut-out

For optimum sealing, we recommend using the sealing frame

which can be purchased as an accessory (part no. 40091-19000).

Installation with the sealing frame is described in the installa-

tion instructions supplied with it.

Installation of the unit in vehicles with an existing skylight:

The cut-out must measure 400 x 400 mm.

Remove the existing skylight (increase the size of the cut-out

if necessary).

Remove seal residue and unevenness.

Fill screw holes with body sealant.

400

For the remaining installation steps, please refer to “Prepara-

tion for mains cable connection”.

–

Installation in a new cut-out

Vehicles without an existing cut-out:

required cut-out 350 x 380 mm

Place the template in the installation location on the vehicle

and mark and cut out the cut-out (350 x 380 mm).

Mark out the 4 holes (10 mm) for attaching the brackets and

drill through the roof.

380

350

Preparation for mains cable connection

A leadthrough for the mains cable to the connection point

should be provided in the intermediate ceiling, for example.

Lift the unit onto the roof, holding it in a horizontal position,

and insert it into the cut-out. The arrow points in the vehicle‘s

direction of travel.

If the unit has been turned over or was not horizontal at

all times, you must wait 2 hours before switching it on.

Slide the unit forward in the cut-out as far as it will go.

Remove the protective film.

Truma aventa making clicking noise. Other than the noise, which gets louder with use, the unit works perfectly. Has anyone else had this problem?
Bev Submitted on 7-4-2023 at 08:16
Reply Report abuse
My truma aventa is making a ticking noise. Has got a solution due this problem. The unit works perfectly otherwise Submitted on 7-4-2023 at 08:13
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Truma Aventa comfort in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 3,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Truma Aventa comfort Manual

Product: