753360
14
Zoom out
Zoom in
Previous page
1/17
Next page
14 EN
cordless tacker PTNS 10-20V
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Troubleshooting tasks which require the housing to be opened
must only be carried out by an authorized specialist electrical
company or by Trotec.
Light smoke or odour is emitted during the first use:
This is not a fault. These phenomena disappear after a
brief runtime.
The battery does not charge:
Check whether the battery is inserted correctly in the quick
charger.
Slide the battery into the quick charger in a way that the
battery terminals engage in the quick charger. The battery
must lock in place in the quick charger.
Check the power connection.
Check the power cable and mains plug for damage.
Check the on-site fusing.
Check the quick charger for damage. If the quick charger
is damaged, stop using it. Contact the Trotec customer
service.
Check the battery terminals for dirt. Remove any dirt.
The battery might be defective and have to be replaced.
Only use batteries of the same type.
The device does not start:
The battery power might be too low. Recharge the battery.
Check whether the battery is correctly connected to the
device.
Slide the battery onto the device in a way that the battery
terminals engage. The battery must lock in place in the
device.
Check the battery terminals for dirt. Remove any dirt.
The tacker guide nose is not properly pushed on the
workpiece. The trigger(2) is linked to the movable tacker
guide nose(5) and will only trigger if the tacker guide nose
is pushed on the workpiece.
Info
Wait for at least 10 minutes before switching the
device back on.
A wire nail or staple is jammed in the device:
Warning
Make sure that the battery has been removed from the
device!
Make sure not to hold the device by the trigger when a
staple or wire nail is jammed inside!
The trigger could be actuated by accident while
removing a jammed staple or wire nail.
Open the magazine release and remove the wire nail or
staple.
No staple or wire nail coming out of the device:
Check whether the wire nails have been inserted according
to the mark(20).
Check the magazine filing level indication(3). If necessary,
insert new staples/ wire nails into the magazine.
Staple or wire nail does not penetrate deeply enough/
hardly penetrates the material:
Check the impact force regulator and select a lower or
higher impact force stage, if required.
The device becomes hot:
Keep the venting slots clear to prevent the motor from
overheating.
Info
Wait for at least 10 minutes before switching the
device back on.
The device still does not operate correctly after these
checks:
Please contact the customer service. If necessary, bring the
device to an authorised specialist electrical company or to
Trotec for repair.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PTNS10-20V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PTNS10-20V in the language / languages: English as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PTNS10-20V

Trotec PTNS10-20V User Manual - German - 18 pages

Trotec PTNS10-20V User Manual - Dutch - 17 pages

Trotec PTNS10-20V User Manual - French - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info