753906
11
Zoom out
Zoom in
Previous page
1/15
Next page
EN 11
sabre saw PRCS 10-850
Operation
Tips and notes on handling the sabre saw
General information:
Keep the venting slots clear to prevent the motor from
overheating.
Check the tool in the tool holder for proper fit before every
application. The tool must be firmly locked in place in the
designated holding fixtures in the tool holder.
Before every application, make sure that you have selected
the correct tool for the intended use.
Sawing:
Before sawing wood, chipboards, building materials etc.,
check the above for foreign objects, e.g. nails, screws or
similar. If required, remove the foreign objects or use a
suitable saw blade.
Only use intact, flawless saw blades. Bent, blunt or
otherwise damaged saw blades could break.
When sawing lightweight construction materials, make
sure to observe the legal regulations and
recommendations of the material manufacturers.
Use a narrow saw blade when sawing tight curves.
If the saw blade gets jammed in the workpiece, switch off
the power tool immediately. The sawing gap should be
slightly widened with a suitable tool so that you can pull
out the power tool.
Switch on the power tool and guide it towards the
workpiece to be processed. Place the guide shoe on the
surface of the workpiece. Process the workpiece with an
even forward motion and contact pressure. After
completing the sawing operation, switch off the power
tool.
The saw blade should not be longer than required for the
intended cut.
Plunge-cutting:
Only soft materials such as plasterboard or the like may be
processed using the plunge-cutting method. Do not
process any metals using the plunge-cutting method.
Use short saw blades for plunge-cutting.
First place the edge of the guide shoe(9) on the workpiece
before switching the power tool on, see Schematic
representation plunge-cutting. Note that the saw blade
must not be in contact with the workpiece.
Select the maximum stroke rate and allow the saw blade
to slowly plunge into the workpiece. To do so, bring the
saw blade closer to the workpiece while maintaining
contact between the edge of the guide shoe(9) and the
workpiece.
As soon as the guide shoe(9) rests on the workpiece, you
can continue working along the cutting line.
Schematic representation plunge-cutting:
9
Flush cutting:
Using elastic bi-metal saw blades you can saw off
protruding objects such as water pipes or the like directly
at the wall.
Make sure that the saw blade extends beyond the
diameter or thickness of the object, otherwise there is a
risk of kickbacks.
Apply lateral pressure on the power tool until the bi-metal
saw blade and the side of the guide shoe are positioned
against the wall, see Schematic representation flush
cutting.
Saw through the object applying constant lateral pressure.
Schematic representation flush cutting:
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PRCS 10-850 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PRCS 10-850 in the language / languages: English as an attachment in your email.

The manual is 2,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PRCS 10-850

Trotec PRCS 10-850 User Manual - German - 17 pages

Trotec PRCS 10-850 User Manual - Dutch - 17 pages

Trotec PRCS 10-850 User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info