753366
14
Zoom out
Zoom in
Previous page
1/21
Next page
14 EN
cordless planer PPLS 10-20V
Operation
Tips and notes on handling the planer
General information:
At the beginning, only position the front part of the device
on the workpiece.
Only guide the part of the device where the cutting head is
located against the workpiece after the device has been
switched on.
Guide the device over the workpiece in an even forward
motion. Hold onto the device with both hands; one hand at
the rotary knob(4) and the other one at the device
handle(24). The front and rear base plate should fully rest
on the workpiece.
Planing:
Use sharp blades only. Worn blades can yield an uneven
result.
If you want to use the full planing width or process hard
wood, we recommend choosing a small cutting depth and
working with a slow forward motion.
For a higher surface quality, we recommend applying the
pressure on the centre of the device and working with a
slow and even forward motion.
Using the lift-off device
The lift-off device serves as an aid when putting the device
down and for protecting the workpiece.
Note
Never remove the lift-off device from the device. A
missing lift-off device causes instability of the device
and can damage the workpiece or device.
Please proceed as follows to use the lift-off device:
1. Make sure that the lift-off device(19) folds down when the
device is lifted, and put the device down safely.
19
2. If you want to continue working, first position the front
base plate and, while advancing, bring the rear base plate
into contact with the workpiece. The lift-off device(19) will
automatically fold up.
19
Switching the device on and off
Wear your personal protective equipment when working with
the device.
1. Check whether the set cutting depth is suitable for the
intended application.
2. Check whether the workpiece is secured and the worktop
prepared correspondingly.
3. Position the front base plate on the workpiece.
4. Press the start lock(23) to be able to actuate the on/off
switch.
5. Press the on/off switch(1) and hold it during operation.
1
23
6. Slowly guide the device along the workpiece while
applying slight, even pressure.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PPLS10-20V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PPLS10-20V in the language / languages: English as an attachment in your email.

The manual is 4,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PPLS10-20V

Trotec PPLS10-20V User Manual - German - 21 pages

Trotec PPLS10-20V User Manual - Dutch - 21 pages

Trotec PPLS10-20V User Manual - French - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info