753335
10
Zoom out
Zoom in
Previous page
1/15
Next page
10 EN
engraving pen PEGS 10-230V
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
Switch off the device.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
If required, allow the device to cool down.
Clean the device according to the Maintenance chapter.
Store the device according to the Storage chapter.
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Troubleshooting tasks which require the housing to be opened
must only be carried out by an authorized specialist electrical
company or by Trotec.
Beim ersten Gebrauch tritt leichter Rauch oder Geruch auf:
Hierbei handelt es sich nicht um einen Fehler oder eine
Störung. Nach kurzer Laufzeit verschwinden die Merkmale.
Das Gerät läuft nicht an:
Überprüfen Sie den Netzanschluss.
Check the power cable and mains plug for damages. If you
notice damages, do not try to take the device back into
operation. To avoid safety hazards, do not perform any
repairs. Send the device to a specialist electrical company
or to Trotec to have the power cable and mains plug
replaced.
Überprüfen Sie die bauseitige Netzabsicherung.
Info
Wait for at least 10 minutes before switching the
device back on.
The device becomes hot:
Note
The device is not suitable for continuous operation.
Over a period of 10minutes, do not use the device for
more than 2minutes in continuous operation. Allow the
device to cool down for the remaining time.
If the device overheats nonetheless, switch the device
off and disconnect it from the mains.
Allow the device to cool down sufficiently before
switching it back on.
Info
Wait for at least 8minutes before switching the device
back on.
The device works, however, the engraving is hardly visible
or not visible at all:
Select a higher stroke depth by turning the setting
wheel(2) for the strole depth selection in + direction.
Check the engraving bit(4), if the engraving bit is worn,
replace it by a new one.
Note
Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PEGS 10-230V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PEGS 10-230V in the language / languages: English as an attachment in your email.

The manual is 1,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PEGS 10-230V

Trotec PEGS 10-230V User Manual - German - 15 pages

Trotec PEGS 10-230V User Manual - Dutch - 15 pages

Trotec PEGS 10-230V User Manual - French - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info