753335
7
Zoom out
Zoom in
Previous page
1/15
Next page
EN 7
engraving pen PEGS 10-230V
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
Before transporting the device, observe the following:
Switch off the device.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Allow the device to cool down.
Storage
Before storing the device, observe the following:
Switch off the device.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Allow the device to cool down.
Clean the device as described in the Maintenance chapter.
When the device is not being used, observe the following
storage conditions:
dry and protected from frost and heat
ambient temperature below 45°C
protected from dust and direct sunlight
Start-up
Unpacking the device
Take the device and the accessories out of the packaging.
Warning of electrical voltage
Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!
Check the contents for completeness and look for
damages.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Dispose of the packaging material according to the
national regulations.
Replacing the engraving bit
The engraving bit must be replaced when it is worn and if it no
longer supplies the desired engraving results.
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Warning of hot surface
The insertion tool might still be hot after the
application. Burn hazard when touching the insertion
tool.
Do not touch the insertion tool bare-handed!
Wear protective gloves!
üEnsure that a new engraving bit is at hand
1. Rotate the latch of the engraving bit(5) in counter-
clockwise direction and remove it.
5
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PEGS 10-230V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PEGS 10-230V in the language / languages: English as an attachment in your email.

The manual is 1,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PEGS 10-230V

Trotec PEGS 10-230V User Manual - German - 15 pages

Trotec PEGS 10-230V User Manual - Dutch - 15 pages

Trotec PEGS 10-230V User Manual - French - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info