753918
15
Zoom out
Zoom in
Previous page
1/18
Next page
EN 15
belt sander PBSS 10-600
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
Switch off the device.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
If required, allow the device to cool down.
Remove the tool from the device (see Start-up chapter).
If attached, disconnect the dust extraction system from the
device.
Clean the device according to the Maintenance chapter.
Store the device according to the Storage chapter.
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Troubleshooting tasks which require the housing to be opened
must only be carried out by an authorized specialist electrical
company or by Trotec.
Light smoke or odour is emitted during the first use:
This is not a fault. These phenomena disappear after a
brief runtime.
The device does not start:
Check the power connection.
Check the power cable and mains plug for damages. If you
notice damages, do not try to take the device back into
operation. To avoid safety hazards, do not perform any
repairs. Send the device to a specialist electrical company
or to Trotec to have the power cable and mains plug
replaced.
Check the on-site fusing.
Info
Wait for at least 10 minutes before switching the
device back on.
The abrasive belt does not move although the motor is
running:
Make sure that the abrasive belt does not grind into the
housing. Adjust the belt run if required, see chapter
Adjusting the belt run.
Make sure that there is no workpiece debris blocking the
drive. Remove the blockages, if any.
Check whether you are using an abrasive belt that is
suitable for this device.
The motor slows down:
Check whether the device is overloaded by the workpiece.
Reduce the pressure applied on the workpiece.
Check whether the workpiece is suitable for the tasks to
be carried out.
The surface of the workpiece is not smooth or the grinding
performance is insufficient:
Check whether the selected abrasive belt is suitable for the
material to be processed.
If the abrasive belt is worn, replace it with a new one, see
chapter Changing the abrasive belt.
Check the belt speed setting. It must be suitable for both
the abrasive belt and the material.
Select a higher speed level by turning the setting wheel for
the belt speed selection to the desired level.
The device becomes hot:
Check whether the selected abrasive belt is suitable for the
tasks to be carried out.
Make sure not to exert too much pressure on the device
during grinding.
Keep the venting slots clear to prevent the motor from
overheating.
Wait for at least 10 minutes before switching the device
back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.
Maintenance
Activities required before starting maintenance
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
Switch off the device.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Allow the device to cool down completely.
Warning of electrical voltage
Maintenance tasks which require the housing to be
opened must only be carried out by authorised
specialist companies or by Trotec.
Notes on maintenance
Inside the device, there are no parts that need to be maintained
or lubricated by the user.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PBSS 10-600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PBSS 10-600 in the language / languages: English as an attachment in your email.

The manual is 2,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PBSS 10-600

Trotec PBSS 10-600 User Manual - German - 20 pages

Trotec PBSS 10-600 User Manual - Dutch - 19 pages

Trotec PBSS 10-600 User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info