753327
12
Zoom out
Zoom in
Previous page
1/14
Next page
12 EN
heat gun HyStream 2000
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
Warning of hot surface
The insertion tool might still be hot after the
application. Burn hazard when touching the insertion
tool.
Do not touch the insertion tool bare-handed!
Wear protective gloves!
1. Switch the on/off switch(2) to position1 and the fan speed
to stage5. Leave the device running at the cold setting for
a brief period.
2. Put the device up in a vertical position allowing it to cool
down sufficiently.
3. Switch off the device by sliding the on/off switch(2) to
position0.
4. Hold onto the mains plug while pulling the power cable out
of the mains socket.
5. Clean the device according to the Maintenance chapter.
6. Store the device according to the Storage chapter.
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Troubleshooting tasks which require the housing to be opened
must only be carried out by an authorized specialist electrical
company or by Trotec.
Light smoke or odour is emitted during the first use:
This is not a fault. These phenomena disappear after a
brief runtime.
The device does not start:
Check the power connection.
Check the power cable and mains plug for damages. If you
notice damages, do not try to take the device back into
operation. To avoid safety hazards, do not perform any
repairs. Send the device to a specialist electrical company
or to Trotec to have the power cable and mains plug
replaced.
Check the on-site fusing.
The device has automatically switched itself off:
Keep the air inlet clear to prevent the motor from
overheating.
Check whether the overheating protection has tripped, see
chapter Safety.
Info
Wait for at least 10 minutes before switching the
device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec HyStream 2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec HyStream 2000 in the language / languages: English as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec HyStream 2000

Trotec HyStream 2000 User Manual - German - 15 pages

Trotec HyStream 2000 User Manual - Dutch - 15 pages

Trotec HyStream 2000 User Manual - French - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info