753934
8
Zoom out
Zoom in
Previous page
1/12
Next page
8 EN
laser distance measuring device BD 11
Carrying out single distance measurement
1. Briefly press the Switch-on/ measurement button(7) to
activate the laser if it is switched off.
2. Point the laser at the target area.
3. Briefly press the Switch-on/ measurement button(7)
again to perform a distance measurement.
ðThe measured value is displayed in the lower
measurement value display(20) immediately.
Adding/ subtracting measured values
1. Carry out a single distance measurement.
ðThe measured value is indicated on the display.
2. To add a measured value, briefly press the Plus/ minus
button(8) one time.
3. To subtract a measured value, briefly press the Plus/
minus button(8) twice.
4. Press the Switch-on/ measurement button(7) to
determine the next measured value.
ðThe overall result will be indicated in the lower
measurement value display(20). The individual
measured values will be indicated in the upper
measurement value displays(17).
Performing an area measurement
1. Briefly press the Function button(10) one time.
ðThe symbol for area measurement appears on the
display.
2. Briefly press the Switch-on/ measurement button(7) to
carry out the first measurement (e.g.length).
ðThe measured value is indicated in the upper
measurement value display(17).
3. Briefly press the Switch-on/ measurement button(7)
again to carry out the second measurement (e.g.width).
ðUpon pressing the Switch-on/ measurement button(7)
for the second time the device calculates the area and
displays this value in the lower measurement value
display(20). The most recently measured value will be
indicated in the upper measurement value display(17).
Performing a volume measurement
1. Briefly press the Function button(10) twice.
ðThe symbol for volume measurement appears on
the display.
ðThe side to be measured is indicated by red arrows in
the measurement value display.
2. Briefly press the Switch-on/ measurement button(7) to
carry out the first measurement (e.g.length).
ðThe measured value is displayed in the upper
measurement value display(17).
3. Briefly press the Switch-on/ measurement button(7)
again to carry out the second measurement (e.g.width).
ðThe measured value is additionally displayed in the
upper measurement value display(17).
4. Briefly press the Switch-on/ measurement button(7)
again to carry out the third measurement (e.g.height).
ðThe measured value is additionally displayed in the
upper measurement value display(17).
ðUpon pressing the Switch-on/ measurement button(7)
for the third time the device independently calculates
the volume and displays this value in the lower
measurement value display(20).
Performing a non-stop/ min and max measurement
Use the non-stop measuring function to correlate
measurements e.g. with construction drawings. With this
measurement method the device can be moved closer toward
the target with the measured value being recalculated roughly
every 0.5seconds. The corresponding maximum and minimum
measured values are displayed in the first and second line of the
upper measurement value display(17) respectively.
For instance, you can direct the laser beam at a wall and then
retreat from it step by step. Keep reading the measured values
until the desired distance is achieved.
1. Press and hold the Switch-on/ measurement button(7) for
approx.2s.
ðThe indications , and Δ(13) appear on the
display.
2. With reference to the target point, move the device slowly
back and forth as well as up and down (e.g.in a corner).
3. Briefly press the Switch-on/ measurement button(7) to
terminate the non-stop measurement.
ðThe maximum and minimum measured values and the
differenceΔ(13) between these two are indicated on
the display. Additionally, the last measured value will be
displayed in the lower measurement value display(20).
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec BD11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec BD11 in the language / languages: English as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec BD11

Trotec BD11 User Manual - German - 12 pages

Trotec BD11 User Manual - Dutch - 12 pages

Trotec BD11 User Manual - French - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info