Manual Triton T20CH (page 6 of 40) (English, German, Dutch, French, Italian, Spanish)

665033

Zoom out

Zoom in

1/40

r) If you are interrupted when operating the drill, complete the process and switch off

before looking up.

s) Where possible, use clamps or a vice to hold your work.

t) ALWAYS disconnect the hammer drill from the electric supply before changing a

chisel or drill bit.

u) Examine the chuck regularly for signs of wear or damage. Have damaged parts

repaired by a qualiﬁed service centre.

v) ALWAYS wait until the drill has come to a complete stop before putting it down.

w) On completion of the work, disconnect the tool from the power source and remove

bit from the machine.

x) Periodically check all nuts, bolts and other ﬁxings and tighten where necessary.

Battery and Charger Safety

Use the battery charger correctly

• Refer to the section of this manual relating to use of the battery charger before attempting

to charge the battery pack.

• Do not attempt to use the charger with any batteries other than those supplied. Keep your

battery charger clean; foreign objects or dirt may cause a short or block air vents. Failure

to follow these instructions may cause overheating or ﬁre

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent

or similarly qualiﬁed persons in order to avoid a hazard

• Children should be supervised to ensure that they do not play with the appliance.

WARNING: Do not recharge non-rechargeable batteries

Use batteries correctly

• Only charge batteries using the charger provided. Only use batteries provided with this

power tool, or others recommended by the supplier. Keep batteries clean; foreign objects

or dirt may cause a short. Allow batteries to cool for 15 minutes after charging or heavy

use. Failure to follow these instructions may cause overheating or ﬁre.

• When not in use batteries should be stored at room temperature (approx. 20˚C). Ensure

that batteries cannot accidentally short in storage.

NOTICE for Battery Packs

• DANGER – Risk of battery packs include burn hazard, ﬁre hazard and explosion hazard

• CAUTION - Do Not Open, Disassemble, Crush, Heat above 60 degree C or incinerate. Do

Not dispose of in ﬁre or similar.

• CAUTION – for Primary batteries, do not charge.

• CAUTION – only charge battery with charger model T20BC. For Safety use of battery

charger, make reference to the instruction manual of the battery charger.

• CAUTION - Follow Manufacturer’s Instructions

Battery and charger safety features

The battery pack and charger are ﬁtted with a number of safety features which may be

triggered during charging or operation:

• Over-charge protection: Charger automatically switches off when the battery pack has

reached full charge capacity, protecting the internal components of the battery pack

• Over-discharge protection: Prevents the battery from discharging beyond the

recommended lowest safety voltage

• Over-heat protection: Sensor switches off if the battery becomes too hot during operation.

This can happen if the tool is overloaded or being used for extended periods of time. Up to

30 minutes cooling time may be required depending on the ambient temperature

• Overload protection: Battery temporarily stops if it is overloaded or the maximum current

draw is exceeded, protecting the internal components. The battery will resume normal

operation when the current draw returns to a normal safe level. This may take a few

seconds

• Short circuit protection: The battery pack will stop working immediately if a short circuit

occurs, this prevents damage to the battery pack or tool

Product Familiarisation

1. Keyless Chuck

2. Torque Adjustment Collar

3. Mode Selector

4. Gear Selector

5. Forward/Reverse Switch

6. Speed Control Trigger Switch

7. Battery Release

8. Belt Clip

9. Battery Pack

10. LED Work Light

11. Battery Charger

Accessories (not shown):

• Soft carry case

Note: This manual may be supplied with different package conﬁgurations and supplied

accessories may vary.

Intended Use

• Battery operated drill with screwdriver, drill and hammer drill functions suitable for

medium duty drilling and driving tasks

Unpacking Your Tool

• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features

and functions

• Ensure that all parts of the tool are present and in good condition. If any parts are missing

or damaged, have such parts replaced before attempting to use this tool

Before Use

• This cordless combi hammer drill has been shipped in a low charge condition. Charge the

battery before use

Removing a battery

• To remove the Battery (9) from the tool, press the Battery Release (7), then slide the

Battery off towards the front of the drill

WARNING: DO NOT try to remove the Battery without pressing the Battery Release. The drill or

Battery could be damaged.

Fitting a battery

• To ﬁt a charged battery, slide it on to the battery slot at the base of the power tool until it

clicks and locks into position

Note: Make sure the Battery (9) and drill are lined up correctly. If the Battery does not slide

into the tool easily, don’t force it. Instead, slide the Battery out of the power tool again, check

the top of Battery and the drill battery slot are clean and undamaged and that the contacts

are not bent.

Battery charger operation

• The Battery Charger (11) and Battery (9) may become warm while charging. This is normal

and does not indicate a problem

• Use the Battery Charger at normal room temperatures whenever possible. To prevent

overheating, do not cover the Battery Charger and do not charge the Battery in direct

sunlight or near sources of heat

If the battery does not charge properly:

• Check current at power outlet by plugging in a lamp or other appliance

• If charging problems persist, have the power tool, Battery and Battery Charger checked by

an electrician or a power tool technician

Charging the battery

1. Depress the Battery Release Button (7) and remove the Battery (9) from the tool

2. Insert the Battery into the Battery Charger (11). Do not use excessive force when inserting

the Battery. If it does not slide into place easily, it is not being inserted correctly

3. Initially only the green LED may ﬂash as it evaluates the status of the battery. When

charging, the red LED will illuminate and the green LED will be OFF

4. When the Battery is fully charged the red LED will be OFF and the green LED will

illuminate

5. The Battery Charger will constantly monitor the condition of the Battery when charging

6. Remove the Battery as soon as possible when completely charged

7. Disconnect the charger from the power supply and store in a clean, dry environment out of

the reach of children

• Normal battery charging time is approximately 80 minutes for a recently fully discharged

4Ah battery at normal temperature. Charging times will vary outside these conditions.

2Ah battery charging time will be approximately 40 minutes

• You do not need to fully discharge the Battery before recharging but you should not

attempt to recharge a Battery that is already fully charged

• You can interrupt charging at any point to use the battery. Under normal conditions the

charger charges at a higher rate but reduces the charging rate as the battery becomes

fully charged. An 80% charge is achieved after 60 minutes of charging for a 4Ah battery

and 30 minutes for a 2Ah battery

100901_Z1MANPRO1.indd 6 11/07/2016 14:39

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Triton T20CH in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Triton T20CH Manual

Product: