Manual Triton T12RS (page 7 of 108) (English, German, Dutch, French, Italian, Polish, Portuguese, Portuguese, Spanish)

665057

Zoom out

Zoom in

1/108

Unpacking Your Tool

• Carefully unpack and inspect your tool. Fully familiarise yourself with all its

features and functions

• Ensure that all parts of the tool are present and in good condition. If any

parts are missing or damaged, have such parts replaced before attempting

to use this tool

Before Use

• The supplied battery pack has been shipped in a low-charge condition.

Charge the batteries before use

Battery charger operation

• The Battery Charger (13) and Battery (9) may become warm while

charging. This is normal and does not indicate a problem

• Use the Battery Charger at normal room temperatures whenever possible.

To prevent overheating, do not cover the Battery Charger and do not charge

the Battery in direct sunlight or near sources of heat

If the battery does not charge properly:

• Check current at power outlet by plugging in a lamp or other appliance

• If charging problems persist, have the reciprocating saw, Battery (9) and

Battery Charger (13) checked by an electrician or a power tool technician

Charging the battery

1. Depress the Battery Release Grips (8) and remove the Battery (9) from

the tool

2. Insert the Battery into the Battery Charger (13). Do not use excessive force

when inserting the Battery. If it does not slide into place easily, it is not

being inserted correctly

3. Initially only the green LED may ﬂash as it evaluates the status of the

Battery. When charging the red LED will illuminate and the green LED will

be OFF

4. When the Battery is fully charged the red LED will be OFF and the green

LED will illuminate

5. The Battery Charger will constantly monitor the condition of the Battery

when charging

6. Remove the Battery as soon as possible when completely charged

7. Disconnect the Battery Charger from the power supply and store in a clean,

dry environment out of the reach of children

• Normal battery charging time is approximately 1 hour for a recently fully

discharged battery at normal temperature. Charging times will vary outside

these conditions

• The battery does not need to be fully discharged before recharging but a

fully charged battery must not be charged

• You can interrupt charging at any point to use the Battery. Under normal

conditions the Battery Charger charges at a higher rate but reduces the

charging rate as the Battery becomes fully charged. An 80% charge is

achieved after 1/2hr of charging

3.0Ah High Capacity Battery (optional accessory)

• A high capacity battery is available that provides double the capacity. It

also allows the saw to stand vertically which may be advantageous for

some uses. Please note the full charging time will be approximately 2

hours for the high capacity battery

Note: If the lights on the Battery Charger fail to illuminate according to the

chart above or indicate a fault condition:

• Check the Battery is ﬁrmly seated in the Battery Charger

• Check all connections and that mains power is switched on

Initial charge

• The initial charge will vary depending on the existing charge in the Battery.

Allow the Battery to reach full charge as indicated on the Battery Charger

• After discharging, recharge the Battery completely, as indicated by the LED

on the Battery Charger, for the next 4 to 5 uses. This will ensure that the

Battery is performing to its highest capacity

• Subsequent full charges will take approximately 1 hour, however the

Battery can be recharged when the Battery is only partially discharged

Re-charging the battery

• After use, a li-ion battery must be allowed to cool down before charging

• If a hot battery is inserted into the charger both LEDs will illuminate. The

charger will begin to charge when the battery has cooled sufﬁciently (this

may take several minutes)

Installing the battery

• The Battery should ﬁt easily into the Battery Charger. If the Battery is

difﬁcult to ﬁt, check the condition of the battery and contacts

Battery - length of service

• The length of service from each charging cycle will depend on the type of

workload. The Battery Charger and Battery for this tool have been designed

to provide a long trouble-free working life. The Battery Charger intelligently

monitors the condition of the Battery and selects the ideal charging rate

for the condition of the Battery. It protects the Battery from over-charging

or charging at too high a rate. However, like all batteries, performance will

be reduced over time

To maximise battery life:

• Store and charge the Battery in a cool area. Temperatures above or below

normal room temperature will reduce battery life

• Never store li-ion batteries in a discharged condition. Recharge them

immediately after they are discharged. For storing long term, store fully

charged

• All batteries gradually lose their charge, even li-ion batteries, but the

discharge rate is very low. If the saw is stored for long periods of

time without use, recharge the battery every three to four months and

disconnect the battery from the power tool before it is stored. This practice

will prevent the li-ion battery being damaged when stored

Red

LED

Green

LED

Battery Charger plugged In OFF Flashing

Battery Charger evaluating battery OFF Flashing

Fast charging ON OFF

Highly discharged battery pack slow charging Flashing OFF

Abnormal battery pack temperature charging Flashing OFF

Fully charged OFF ON

Battery pack or battery charger fault Flashing Flashing

Abnormal temperature ON ON

Battery Charging Table

103935_Z1MANPRO1.indd 7 26/09/2014 11:17

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Triton T12RS in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 6,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Triton T12RS Manual

Product: