Manual Triton T12RS (page 6 of 108) (English, German, Dutch, French, Italian, Polish, Portuguese, Portuguese, Spanish)

665057

Zoom out

Zoom in

1/108

Battery tools use and care

a) Recharge only with charger speciﬁed by the manufacturer. A charger

that is suitable for one type of battery pack may create a risk of ﬁre when

used with another battery pack.

b) Use power tools only with speciﬁcally designated battery packs.

Use of any other battery packs may create a risk of injury and ﬁre

c) When battery pack is not in use, keep it away from other metal

objects, like paper clips, coins, keys, nails, screws and other small

metal objects that can make a connection from one terminal to

another. Shorting the battery terminals together may cause a burns or

a ﬁre.

d) Under abusive conditions, liquid may be ejected from the battery;

avoid contact. If contact accidentally occurs, ﬂush with water. If

liquid contact eyes, additionally seek medical help. Liquid ejected

from the battery may cause irritation or burns

Service

a) Have your power tool serviced by a qualiﬁed repair person using

only identical replacement parts. This will ensure that the safety of the

power tool is maintained.

WARNING: Before connecting a tool to a power source (mains switch power

point receptacle, outlet, etc.) be sure that the voltage supply is the same as

that speciﬁed on the nameplate of the tool. A power source with a voltage

greater than that speciﬁed for the tool can result in serious injury to the user,

and damage to the tool. If in doubt, do not plug in the tool. Using a power

source with a voltage less than the nameplate rating is harmful to the motor.

Reciprocating Saw Safety

• Ensure that lighting is adequate

• Keep the area free of tripping hazards

• Wear appropriate safety equipment including eye protection and gloves to

protect against vibration

• Never saw near combustible liquids or gases

• Check for hidden wiring and pipes before sawing

• Use recommended blades only

• Blades must be sharp and not cracked or distorted

• Before starting work, inspect the workpiece and remove all embedded

objects such as nails, screws etc

• Support and secure the workpiece correctly

• When cutting cylindrical wood, use clamps that prevent the workpiece from

turning

• Use the insulated handles when operating power tools. This protects the

operator if the tool accidentally cuts through hidden electrical wiring,

causing the tool to become ‘live’

• Always stand to one side when operating the saw

• Do not use your hands to remove sawdust, chips or waste close to the

blade

• Never reach over the blade to remove waste or off-cuts

• Do not attempt to free a jammed blade until the machine has been

disconnected from the power

• Do not attempt to slow or stop a blade with any object. Let the blade come

to rest naturally

• If you are interrupted when operating the saw, complete the process and

switch off before looking up

• Periodically check the tool for loose nuts, bolts and tighten as necessary

Hold power tool by insulated gripping surfaces, when performing an

operation where the cutting accessory may contact hidden wiring. Cutting

accessory contacting a ‘live’ wire may make exposed metal parts of the power

tool ‘live’ and could give the operator an electric shock.

Use clamps or another practical way to secure and support the workpiece

to a stable platform. Holding the work by hand or against your body leaves it

unstable and may lead to loss of control.

NOTICE for Battery Packs

DANGER - Risk of battery packs include burn hazard and explosion hazard

CAUTION - Do not open, disassemble, crush, heat above 60°C or incinerate.

No not dispose of in ﬁre or similar

CAUTION - for primary batteries, do not charge

CAUTION - only charge battery with charger model T12BC. For safety use of

battery charger, make reference to the instruction manual of the

battery charger

CAUTION - follow manufacturer’s instructions

Battery Charger Safety

Use the battery charger correctly

• Refer to the section of this manual relating to use of the battery charger

before attempting to charge the battery.

• Do not attempt to use the charger with any batteries other than those

supplied. Keep your battery charger clean; foreign objects or dirt may

cause a short or block air vents. Failure to follow these instructions may

cause overheating or ﬁre

• If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or similarly qualiﬁed persons in order to avoid a hazard

• Children should be supervised to ensure that they do not play with the

appliance.

Warning: Do not recharge non-rechargeable batteries

Use batteries correctly

Only charge battery pack using the charger provided. Only use battery pack

provided with this power tool, or others recommended by the supplier. Keep

batteries clean; foreign objects or dirt may cause a short. Allow battery pack

to cool for 15 minutes after charging or heavy use. Failure to follow these

instructions may cause overheating or ﬁre.

When not in use the battery pack should be stored at room temperature

(approx. 20°C). Ensure that the battery pack cannot accidentally short in

storage.

Battery and charger safety features

The battery and charger are ﬁtted with a number of safety features which may

be triggered during charging or operation:

• Over-charge protection: Charger automatically switches off when

the battery has reached full charge capacity, protecting the internal

components of the battery

• Over-discharge protection: Prevents the battery from discharging beyond

the recommended lowest safety voltage

• Over-heat protection: Sensor switches off if the battery becomes too hot

during operation. This can happen if the tool is overloaded or being used

for extended periods of time. Up to 30 minutes’ cooling time may be

required depending on the ambient temperature

• Overload protection: Battery temporarily stops if it is overloaded or the

maximum current draw is exceeded, protecting the internal components.

The battery will resume normal operation when the current draw returns to

a normal safe level. This may take a few seconds

• Short circuit protection: The battery will stop working immediately if a short

circuit occurs, this prevents damage to the battery or tool

WARNING: When used in Australia or New Zealand, it is recommended that

this tool is ALWAYS supplied via Residual Current Device (RCD) with a rated

residual current of 30mA or less.

Intended Use

The Triton T12RS is a versatile cordless reciprocating saw. This tool is optimally

conﬁgured for sawing wood but can also cut a wide range of other materials

when ﬁtted with a suitable blade.

103935_Z1MANPRO1.indd 6 26/09/2014 11:17

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Triton T12RS in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 6,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Triton T12RS Manual

Product: