Manual Triton MSA 200 (page 5 of 32) (English, German, Dutch, French, Italian, Polish, Portuguese, Portuguese, Spanish)

665183

Zoom out

Zoom in

1/32

Page 3

Safety Instructions

Carefully read and understand this manual and any label attached to the tool before use.

Keep these instructions with the product for future reference. Ensure all persons who use this

product are fully acquainted with these instructions.

Even when following these instructions it is not possible to eliminate all residual risk factors.

Use with caution. If you are at all unsure of the correct and safe manner in which to use this

tool, do not attempt to use it.

• Do not force, or attempt to use a tool for a purpose for which it was not designed

• This tool is not intended for industrial use

• The use of any attachment or accessory other than those mentioned in this manual could

result in damage or injury.

• The use of improper accessories could be dangerous, and may invalidate your warranty

• Where possible, always secure work. If appropriate use a clamp or vice, it will allow you to

use both hands to operate your tool

Multi-Stand Safety

• AlWAYS ensure that the stand’s legs are correctly extended, and that all clamping screws

are fully tightened before applying heavy loads

• NEVER load the stand off-centre or in a manner that will cause an imbalance

• NEVER exceed the maximum load capacity (see ‘Speciﬁcation’). Doing so will damage

your stand and may cause serious injuries

• DO NOT stand on this product

• DO NOT use this product for the construction of work platforms

• ALWAYS use a packing piece when clamping materials of less than 30mm thickness

• When clamping easily damaged materials, eg doors, use thin packing on both sides to

avoid damage

• Ensure the stand is securely fastened down when applying non-vertical loads or when on

sloping ground

Intended Use

• This Triton Multi-Stand is a portable tripod workpiece support suitable for a multitude of

different applications

Unpacking Your Tool

• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features and

functions

• Ensure that all parts of the tool are present and in good condition. If any parts are missing

or damaged, have such parts replaced before attempting to use this tool

Before Use

Assembly

• The Triton Multi-Stand is easily assembled. Refer to the ‘Assembly Diagram’ in the back of

this manual, and follow the steps below:

1. Fold the legs of the Main Body Assembly (A) fully outwards. Loosen the round knob and

extend the stem upwards, then tighten

Note: The legs should pivot ﬁrmly. Adjust the nuts on the leg pivot bolts if necessary.

2. Fit the Saddles (B) to the stem using the locating pins on the Saddles as shown

3. Attach the Front Quadrant (C) and Rear Quadrant (D) using the shorter Hex Bolt (E), Small

Washers (F) and Nyloc Nut (G).

WARNING: Do not over-tighten.

4. Fit the Quadrant Washer (I) onto the longer Hex Bolt (J) with the hex head located in the

tabs on the washer. Insert the bolt through the slots in the quadrants, ensuring that it

passes through the washer held within each quadrant and the hole in the lower stem

saddles. Fasten the Large Washer (H) onto the bolt with the Round Knob & Nut (K)

5. Rotate the quadrants until the ﬂat tops are horizontal then gently loosely tighten the Round

Knob

6. Fasten the Head Assembly (L) to the quadrants using the Pan Head Bolts (M). The round

knob on the clamp which is built into the head should be on the same side as the round

knob on the quadrant

7. Adjust the nut tension on the Hex Bolt (E) if necessary. The head should pivot ﬁrmly, and

should lock tightly at any selected angle when the quadrant knob is tightened

Wear hearing protection

Wear eye protection

Wear breathing protection

Wear head protection

Read instruction manual

Caution!

DO NOT use as a step or platform!

Description of Symbols

330090_Z1MANPRO1.indd 5 30/09/2014 09:38

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Triton MSA 200 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 2,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Triton MSA 200 Manual

Product: