457531
10
Zoom out
Zoom in
Previous page
1/84
Next page
18
Winding of the bobbins
Figure 1. Place a yarn pin on the spool pin (no.1).
Guide the thread through the winding thread guide (no.2) to the empty bobbin.
Place the bobbin winding pin (no.18) on the machine.
Wind the thread several times clockwise to the empty bobbin and place it on the
bobbin winding pin (no.18).
Figure 2. Turn the hand wheel (no. 11) clockwise until the thread is tightened.
Start electric winding by pressing the foot control.
When the bobbin is full, release the foot pedal, cut the thread, then remove bobbin
Reverse sewing.
Reverse sewing is suitable for fastening the seam when start seam or finish seam to avoid
stitches loose. Stop the machine firstly, then press the reserve sewing lever (no.10), the
machine can sew reverse. Release the reserve button, the machine can recover to sew
forward. The reverse trace shouldn’t beyound 5 cm.
19
Release of the fabric
Set the needle at the highest position by turning the hand wheel (no. 11) anticlockwise.
Raise the presser foot (no. 8) and remove the fabric backwards.
Cut the threads by using the thread cutter (no. 6) at the side of the machine.
Straight and other stitching
There are three kinds of straight stitches for your choise. Turn the pattern selector (no. 4) to
the one you need. Set the needle at the highest position by turning hand wheel anticlockwise.
Gently pull both threads (about 10 cm) towards rear, raise the presser foot (no. 8), place the
fabric under the presser foot. Gently press down the foot pedal (no. 16) to start sewing. Guide
fabric gently by hand. Stop the needle in its top position, and thread can be pulled out easily.
Raise the presser foot (no. 8) and remove the fabric. This is for all the patterns of your choise.
Notice:
When turning the pattern selector, assure the needle tip is at the upper position, otherwise it
will be bent or damaged or fail to sewing.
When selecting the pattern, set the position correctly, otherwise it will hurt the needle or sew
over the the selected stitch trace. It will be different from the selected pattern.
Thread tension adjustment
For a correct stitch the upper and the lower thread should be even. By turning the thread
tension dial the upper thread can be switched from the left to the right. Use this dial to get the
two threads even.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tristar SM 6000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tristar SM 6000 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info