485386
40
Zoom out
Zoom in
Previous page
1/47
Next page
Notes:
To disable the movement limits, select "Disable Limits" and then press the OK button.
To position the antenna at the center, select "Go to Reference" and then press the OK button.
Once the limits are set, locate the reference satellite.
From the "Antenna Positioner" screen, select "Select Satellite" and then use the buttons
to select the satellite.
Select "Nudge East/West" and then use the buttons to move the antenna.
Find the position where the Signal is strongest.
GB
Select "Set-up Limit" and then press the OK button.
Select "Move East/West". Use the button to move the
antenna to the East Limit position.
Select "Set East Limit" and then press the OK button to
save the East Limit you have set previously.
Select "Move East/West" again. Use the button to move
the antenna to the West Limit position.
Select "Set West Limit" and then press the OK button to
save the West Limit you have set previously.
When doing this, if the position of the antenna is well away from the target satellite, use
"Move East/West" in "Set-up Limit" to move the antenna first.
Alternatively, select "Nudge East/West" and then use the buttons to move the antenna.
Each time you press either button, the antenna will automatically find the satellite.
Once the satellite is located, select "Store Satellite" and then press the OK button.
The position of the satellite is stored.
Select "Recalculate Position" and then press the OK button.
When the message asking you to confirm your selection appears, press the OK button.
Satellite Positions are stored in the "Antenna Positioner". Therefore, you will need to manually
set the position of satellites that the "Antenna Positioner" does not currently support.
Notes:
If you select the stored satellite, the antenna moves in the direction of the satellite's position.
After locating a satellite, perform "Recalculation". This enables you to locate another satellite
automatically by using the currently selected satellite as a reference point. However, this only
provides an approximate position, so you will need to fine-tune the search.
Notes:
9.5 USALS
This convenient function locates the desired satellite by USALS if latitude/longitude of the
receiving place and satellite longitude are known.
Move to USALS mode by using the buttons at the DiSEqC item in the "General Settings"
menu.
Move to "Auto Search" or "Manual Search" to search the desired channel in USALS mode.
Click the DiSEqC item in the Auto Search Menu to open the USALS Setting Popup Menu.
Enter the user location latitude and longitude. Use numeric keys to enter values. Use -
buttons to convert East and West.
Enter the latitude and longitude of the desired satellite. Use numeric keys to enter values. Use
- buttons to convert East and West.
Click Store to save the input information. The antenna will direct itself towards the computed
USALS result.
If it is physically impossible to direct the satellite, an error will be displayed. Press the "Back"
key and enter new information if this happens.
Use the Signal Strength Bar to check if a satellite signal is received from the new antenna
direction.
Use Nudge East/West or Go to Reference to help the antenna work.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Triax DVB S2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Triax DVB S2 in the language / languages: English, German as an attachment in your email.

The manual is 5,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info