485390

Triax DVB 168S Manual

43
Zoom out
Zoom in
Previous page
1/48
Next page
DVB 168 S (GB)-19 050908
www.triax.com
19
Enter the TP information, such as Frequency, Polarization (H / V), Symbol Rate, etc., and
then press the OK button. (Use the Numeric buttons to enter Frequency and Symbol Rate
information, and use the buttons to enter H / V information).
To cancel the entries you have made, press the BACK button or the EXIT button.
Delete a Satellite
Use this to delete the selected satellite. However, you won't be able to delete any of the
satellites, which were set as factory defaults.
Use the CH UP and CH DOWN buttons to select the satellite you want to delete.
Press the button. A message appears, asking for your confirmation.
If you want to delete, press the OK button.
Otherwise, press the "Back" button or the EXIT button.
Modify Satellite TP Information
To modify the TP information, move to the satellite you want and then press the OK button.
The satellite TP information appears on the right side of the screen.
Select the TP information you want to modify and then press the OK button.
Modify the TP information, such as Frequency, Polarization, Symbol Rate, etc., and then
press the OK button. (Use the Numeric buttons to enter Frequency and Symbol Rate
information, and use the buttons to enter H / V information).
After the changes are made, press the OK button to update the TP information.
To cancel the TP information modification process, press the BACK button.
Add Satellite TP Information
Move to the bottom of the screen where the satellite TP information is displayed and then
press the OK button.
Enter the TP information you want to add, such as Frequency, Polarization (H / V), Symbol
Rate, etc. (Use the Numeric buttons to enter Frequency and Symbol Rate information, and
use the buttons to enter H / V information).
Press the OK button to register the TP information.
To cancel the TP information addition process, press the BACK button.
Remove Satellite TP Information
Move to the TP information you want to delete.
Press the LEFT button. A message asking for your confirmation asking for your
confirmation appears.
If you want to delete, press the OK button. Otherwise, press the BACK button or the EXIT
button.
9.9 Data Transfer
This is intended to transfer the channel information on one
receiver to another receiver of the same model / version.
You can also transfer channel information from your PC to
a receiver.
Receiver to Receiver (STB - STB)
Cable Pin Configuration
(1) o --------- o (4)
(2) o --------- o (3)
(3) o --------- o (2)
(4) o --------- o (1)
(5) o --------- o (5)
Use a RS232C cable (cross type, "0-modem") to connect
both receivers.
Go the Main Menu, select "Installation" and then select
menu option "Data Transfer".
Select "3.Ch.Data Sender (STB->STB)" for the receiver
that will send the channel data.
Select "4.Ch.Data Receiver (STB<-STB)" for the receiver
that will receive the channel data.
Press the OK button on both receivers to start the transfer.
… 43 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Triax DVB 168S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Triax DVB 168S in the language / languages: English, German as an attachment in your email.

The manual is 11,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info