485390
40
Zoom out
Zoom in
Previous page
1/48
Next page
DVB 168 S (GB)-16 050908
www.triax.com
16
Select DiSEqC 1.2
or
select USALS
according to your needs. Then please proceed to the
"Antenna Positioner" sub menu in the "Main Menu".
To position the antenna using the DiSEqC 1.2 method,
you will need to set the movement limits first. The reason
for this is to reduce the danger of the antenna coming into
contact with any obstructing object during the antenna
positioning operation.
When the movement limits are set, the antenna only moves within the limits specified.
Select "Set-up Limit" and then press the OK button.
Select "Move East/West". Use the button to move the
antenna to the East Limit position.
Select "Set East Limit" and then press the OK button to save
the East Limit you have set previously.
Select "Move East/West" again. Use the button to move
the antenna to the West Limit position.
Select "Set West Limit" and then press the OK button to
save the West Limit you have set previously.
Notes:
To disable the movement limits, select "Disable Limits" and then press the OK button.
To position the antenna at the center, select "Go to Reference" and then press the OK button.
Once the limits are set, locate the reference satellite.
From the "Antenna Positioner" screen, select "Select Satellite" and then use the buttons to
select the satellite.
Go to "Select Transponder" and select the TP with the strongest signal.
Select "Nudge East/West" and then use the buttons to move the antenna.
Find the position where the Signal is strongest.
When doing this, if the position of the antenna is well away from the target satellite, use "Move
East/West" in "Set-up Limit" to move the antenna first.
Alternatively, select "Nudge East/West" and then use the buttons to move the antenna.
Each time you press either button, the antenna will automatically find the satellite.
9.4 Antenna Positioner / DiSEqC 1.2
The "Antenna Positioner" function of this receiver enables you to use a motorized antenna to view
multiple satellites. Most motor antennas can be controlled by DiSEqC 1.2 technology, some of them
also can be used for USALS. This convenient function locates the desired satellite if the latitude /
longitude of the receiving place and satellite longitude are known.
For setting up such a system it is needed to set the DiSEqC menu item in the "General Settings"
menu accordingly:
Once the satellite is located, select "Store Satellite" and then press the OK button.
The position of the satellite is stored.
Notes:
If you select the stored satellite, the antenna moves in the direction of the satellite's position.
After locating a satellite, perform "Recalculation". This enables you to locate another satellite
automatically by using the currently selected satellite as a reference point. However, this only
provides an approximate position, so you will need to fine-tune the search.
Select "Recalculate Position" and then press the OK button.
When the message asking you to confirm your selection appears, press the OK button.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Triax DVB 168S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Triax DVB 168S in the language / languages: English, German as an attachment in your email.

The manual is 11,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info