817492

Trek eBike Systems 2023 - Bosch Manual

101
Zoom out
Zoom in
Previous page
1/376
Next page
English – 3
Fitting
Fitting and removing the on-board computer
(see figureA)
Fit the lower part of the Kiox into the holder(5) first and tilt
it forward gently until you can feel that the on-board com-
puter is firmly fixed in the magnetic holder.
To remove the on-board computer, hold it by the top end
and pull it towards you until it disengages from the magnetic
holder.
uRemove the on-board computer when you park the
eBike.
The on-board computer can be secured in place to prevent it
from being removed from the holder. To do this, loosen the
headset screw(16) until the Kiox holder can be swivelled
sideways. Put the on-board computer in the holder. Screw
the locking screw (M3 thread, 6mm long) from below into
the thread provided in the on-board computer (using a
longer screw may damage the on-board computer). Swivel
the holder back into place and tighten the headset screw in
accordance with the manufacturer's specifications.
Operation
Before initial commissioning
The Kiox is supplied with a partially charged battery. Before
using it for the first time, this battery must be charged for at
least onehour via the USB port(see "Power supply of the on-
board computer", pageEnglish – 3) or via the eBike sys-
tem.
The operating unit should be attached such that the buttons
are almost perpendicular to the handlebars.
When using the on-board computer for the first time, the lan-
guage selection page is displayed initially. You can then
choose to have essential functions and indications explained
via the<Intro to Kiox> menu item. The menu item can also
be called up at a later time via<Settings>→<Informa-
tion>.
Switching the on-board computer on/off
To switch on and switch off the on-board computer, briefly
press the on/off button(4).
Selecting system settings
Fit the on-board computer in the holder and proceed as fol-
lows with the bicycle stationary:
Go to the status page (use the <button(10) on the control
unit to get to the first display) and call up the (9) <Settings>
with the select button.
You can use the –(11) and +(12) buttons to select the set-
ting you want. You can open the settings, as well as any addi-
tional submenus, using the select button(9). You can use
the <button(10) to go back to the previous menu from any
settings menu.
The following settings can be changed in the <Sys set-
tings>:
–<Brightness>
–<Time>
–<Date>
–<Time zone>
–<24h format>
–<Bright background>
–<Imperial units>
–<Language>
–<Factory reset>
Starting Operation of the eBike
Requirements
The eBike can only be activated when the following require-
ments are met:
– A sufficiently charged eBike battery is inserted (see oper-
ating instructions for the eBike battery).
– The on-board computer is properly fitted in the holder.
Switching the eBike On and Off
The following options are available for switching on the
eBike:
– Once the on-board computer and the eBike battery are
fitted, briefly press the on/off button(4) on the on-board
computer.
– With the on-board computer inserted, push the on/off
button on the eBike battery (bicycle manufacturer-spe-
cific solutions are possible when there is no access to the
eBike battery on/off button; see the eBike battery operat-
ing instructions).
The drive is activated as soon as you start pedalling (except
if you are using the walk assistance function or if the assist-
ance level is set to OFF). The drive power varies depending
on the assistance level set.
As soon as you stop pedalling when in normal operation, or
as soon as you have reached a speed of25/45km/h, the
drive switches off the assistance. The drive is automatically
reactivated as soon you start pedalling again and the speed
is below25/45km/h.
The following options are available for switching off the
eBike:
– Briefly press the on/off button(4) of the on-board com-
puter.
– Switch off the eBike battery using its on/off button (bi-
cycle manufacturer-specific solutions are possible when
there is no access to the eBike battery on/off button; see
the bicycle manufacturer operating instructions).
– Remove the on-board computer from its holder.
If no power is drawn from the drive for about10minutes
(e.g. because the eBike is not moving) and no button is
pressed on the on-board computer or the operating unit of
the eBike, the eBike will switch off automatically.
Power supply of the on-board computer
If the on-board computer is in the holder(5), a sufficiently
charged eBike battery is inserted into the eBike and the
Bosch eBike Systems 1 270 020 XBK | (14.02.2023)
101
… 101 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trek eBike Systems 2023 - Bosch at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trek eBike Systems 2023 - Bosch in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 20.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info