775412
4
Zoom out
Zoom in
Previous page
1/6
Next page
67
1. Remove the battery cover from the back
side of the computer using a
narrow flat blade screwdriver.
2. Install the battery so that the
positive "+" side of the battery is visible,
and replace the battery cover.
CAUTION: On the bottom of the computer
head next to the battery door is a small
recessed button. This is the Auto Clear
Button. Pressing this button will clear all
memories and reset all functions to their
default values.
All Clear Button
COMPUTER SET UP
Battery Installation
BUTTON FUNCTIONS
PROGRAMMING YOUR TREK
SENSOR CYCLE COMPUTER
Setting the Clock
1. Press the mode key to advance
to MXS/Clock display.
2. Press and hold the mode key for over 2
seconds until hours setting
begins to flash.
3. Press the adjust key to adjust hours
setting, press the mode key to confirm and
advance to minutes setting.
4. Press the adjust key (hold for fast
advance) to adjust the minutes, and press
the mode key to confirm setting and enter
normal display mode.
Mode Button
Adjust
Button
Setting Miles/ Kilometers and
Wheel Size
1. Press mode computer key to enter
AVS/ODO mode.
2. Press and hold mode key for over 2 sec-
onds until m/h begins to flash.
3. Press adjust key to select miles (m/h) or
kilometers (km/h) display.
4. Press mode key to confirm choice and
advance to wheel size setting.
5. Adjust the flashing digit with the adjust
button, confirm choice by pressing mode
button, and advance to next flashing digit.
6. Adjust and/or confirm all flashing
digits.
Wheel Size Setting
The wheel size setting number is equal to
the distance, in millimeters, that your front
wheel travels during one complete revolu-
tion. Each time the wheel magnet passes
the sensor unit on your fork, the sensor
sends an impulse to the computer telling it
that your wheel has completed one revolu-
tion. The computer calculates this distance
vs. time to give you accurate readings for
the various modes.
Determining Wheel Size Setting
There are three methods for determining the
wheel size setting. For the most accurate
computer readings, it is best to measure the
actual distance that your wheel travels in
one complete revolution. This method is
called a wheel roll out.
The Sensor is equipped with 2 buttons that
control the function of the unit.
1. MODE
Changes the Main Screens of the Sensor
2. ADJUST
Adjusts digits while programming and
activates ATM lap timer.
Perform the wheel roll out on a hard,
flat, smooth surface such as a garage or
basement floor.
Make sure your tires are properly inflat-
ed.
1. Position your bike so that the valve stem
of the front wheel is at its bottom most
position. Mark the spot on the floor directly
under the center of the valve stem using a
piece of tape or chalk.
2. Roll the bicycle forward in a straight line,
while putting downward pressure on the han-
dlebars to simulate rider weight. When the
wheel has completed one revolution and the
valve stem is at its bottom position, mark the
floor directly under the center of the valve
stem with tape or chalk. Measure the distance
between the two marks in millimeters. (Note:
Conversion of in. to mm. is 1 in.=25.4 mm.)
This is your wheel setting number. You can
repeat this procedure and average your results.
We recommend that you record your wheel set-
ting numbers here for future reference.
Method One: Wheel Roll Out
Sensor 1.0 97 6/12/00 11:17 AM Page 8
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trek 1997 sensor at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trek 1997 sensor in the language / languages: English as an attachment in your email.

The manual is 0.09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info