775412

Trek 1997 sensor Manual

3
Zoom out
Zoom in
Previous page
1/6
Next page
The Trek Sensor Computer attaches to
the mounting bracket by sliding the unit
onto the bracket from the back until it
snaps firmly into position. To remove the
computer from the bracket, place your
thumb against the back of the mounting
bracket and pull the computer toward you
with your index finger.
45
Maximum Speed (MXS)
The Maximum Speed reached during a ride is
displayed in 0.1 mi/Km increments on the
top line, with the MXS icon. Maximum
Speed is stored in
memory and is updated each time a new,
higher speed is reached.
CLOCK (CLK)
The 12 hour clock is displayed on the lower
line, indicated by the CLK icon.
ATM “Lap Timer” Display
A unique ATM “Lap Timer” display allows
you to lock the display at the end of a ride
segment and view the ATM, DST, AVS
and MXS at a later time.
This is especially useful at the end of a race,
allowing you time to cool down without
adding time to your Stopwatch.
As you cross the finish line, press the left
key for over 1 second to freeze information
on the display. You may continue to ride,
viewing the information locked on the flash-
ing locked display. The computer will con-
tinue to record information and store it in
memory. Press the left key to update the
current display information.
RESETTING THE COMPUTER
In SPD/ATM mode, press both keys for over
two seconds to clear ATM, DST, AVS and
MXS display.
SLEEP MODE
To conserve battery power, the computer
will enter the ‘Sleep’ mode after 5 minutes
of no speed input, blanking the display.
Press any key to enter normal operating
modes.
(Note: Unit will not enter sleep mode in
setting function mode.)
1. Position the sensor unit to the inside of
either the right of left fork blade
anywhere from 3-6 inches up from the fork
blade tip. Attach the sensor to the fork
blade with the quick ties but do not tighten
the ties completely until final adjustment is
complete.
INSTALLATION
Sensor and Wheel Magnet
2. Attach the wheel magnet to a spoke,
aligning the magnet with the sensor so it
faces and intersects the bottom polished
line on the sensor. The magnet should have
1-2 mm clearance from the sensor. If the
sensor and magnet are too close or touch-
ing, rotate the sensor unit toward the back
of the fork blade until adequate clearance is
achieved. Carefully tighten the quick ties
making sure you maintain the proper space
between the magnet and the sensor. Trim
the excess quick tie strap using a scissors
or fingernail clipper. Tighten the magnet
screw, but be careful not to over tighten as
this can damage the fitting.
Sensor Wiring and Bracket
1. Route the sensor wire up the back of the
fork blade or wind the wire around the
blade, making sure that the wire is not
loose and that you leave enough wire to
reach the handlebar. Secure the wire to the
fork blade immediately above the sensor
and at the top of the fork blade, using the
adhesive strips
that are provided or electrical tape.
2. Wind the wire upward around the front
brake cable until the wire is adjacent to the
handlebar, allowing enough slack for free
movement of the steering assembly cables.
3. Attach the bracket to the handlebar on
either side of the stem. The bracket goes
onto the handlebar with the wire toward the
rider side of the bar. Use the appropriate
rubber shim between the bracket and han-
dlebar to provide a secure fit.
Shims will
prevent slipping
Attaching the Computer to
the Bracket
Sensor 1.0 97 6/12/00 11:17 AM Page 6
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trek 1997 sensor at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trek 1997 sensor in the language / languages: English as an attachment in your email.

The manual is 0.09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info