732484
8
Zoom out
Zoom in
Previous page
1/18
Next page
FAN STRUCTURE
INSTALLATION
1. Fixing screw for the fan covers
2. Protecve front cover
3. Locknut
4. Fan blades
5. Mounng nut
6. Protecve rear cover
7. Motor sha
8. Motor housing
9. Oscillaon buon
10. Speed switches
11. Housing of the switches
12. Fixing screw
13. Upper tube
14. Connecon between the
tubes
15. Lower tube
16. Crossed pedestal
17. Cover
Slide the two bars into each other, creang the crossed pedestal (16).
Use the 4 screws to x the lower tube (15) onto the crossed pedestal (16).
Loosen the connector between the tubes (14) from the lower tube.
Place the cover (17) over the lower tube (15) and let it fall over the crossed pedestal (16).
Place the connector between the tubes (14) back onto the lower tube (15), but don’t ghten the
connector yet.
Slide the upper tube (13) out of the lower tube (15) to extend it.
Re-ghten the connector between the tubes (14) on the lower tube.
Place the housing of the motor (8) and switches (11) onto the upper tube and ghten it to the upper tube (13)
using the xing screw (12).
Loosen the locknut (3) and mounng nut (5) of the motor sha (7).
Slide the protecve rear cover (6) with the handle upwards over the motor sha (7).
Tighten Mounng nut (5) an-clockwise against the fan blades (6).
Schuif de venlatorbladen (4) over de motoras (7).
Tighten the locknut (3) an-clockwise against the fan blades (4).
Turn the clips of the protecve front cover (2) outwards and hang the protecve cover over the edge of the
protecve rear cover. Make sure that the opening at the boom of the protecve front cover is aligned with
the opening at the boom of the protecve rear cover.
Insert the screw (1) through both openings at the boom of the protecve covers and x the covers together
using the nut.
Finally, close the clips around both protecve covers.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17
8
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trebs 99382 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trebs 99382 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info