798690

Traeger Select Pro - BBQ400.03 Manual

6
Zoom out
Zoom in
Previous page
1/18
Next page
SECTION THREE: SUBSEQUENT START-UP
With the Door open, turn the Switch ON (--) and the Temperature/Dial to SMOKE. In
approximately 2 minutes you will notice whitish-gray smoke coming out of the Grill
as the Pellets ignite. After assuring the Pellets have ignited, close the Door and set
the Temperature/Dial to any cooking setting desired. The Grill should be allowed to
pre-heat for approximately 10 minutes with the Door closed before placing food in
the Grill.
WARNING! If at any time, the Grill fails to light or the fire in the Firepot goes out while
cooking or smoking, when sufficient pellets are still in the Pellet Hopper, it is important
to follow these steps. Failure to do so may cause a hazardous “over-firing” of your grill
due to an excess of unburned pellets in the Firepot.
1) DANGER! Turn the Switch OFF (o) and disconnect the Power Cord. If the Grill is still
hot, allow it to thoroughly cool. Open the Door and remove all food, the Porcelain
Grills, Grease Drain Pan and the Heat Baffle.
2) WARNING! Remove all unburned pellets and ash from inside and around the
Firepot. (See instructions for proper handling and disposal of ash in Section
Five)
3) Before replacing the Heat Baffle, Grease Drain Pan and the Porcelain Grills, plug the
power Cord into an appropriate, grounded electrical outlet and restart the Grill. Pellets
should fall into the Firepot and the Hot Rod should begin to heat (it will start to turn
red). CAUTION! Do not touch it.
4) If this procedure is successful, you will soon see flames come out of the Firepot.
Then turn the Switch OFF (o), and let the Grill cool down. Position the Heat Baffle,
the Grease Drain Pan and Porcelain Grill in their proper locations. With the Door
open, turn the Switch ON (--) and the Temperature/Dial to SMOKE. In approximately
2 minutes you will notice whitish-gray smoke coming out of the Grill as the Pellets
ignite. After assuring the Pellets have ignited, close the Door and set the
temperature/Dial to any cooking setting desired.
5) If this procedure is not successful, see Section Six: FREQUENTLY ASKED
QUESTIONS for troubleshooting tips or contact Traeger Technical Support (Section
Seven) to help diagnose the problem before proceeding to the MANUAL LIGHTING
INSTRUCTIONS below.
MANUAL LIGHTING INSTRUCTIONS:
If the Hot Rod only is not operating, the Grill can still be used to cook and smoke using
the MANUAL LIGHTING PROCEDURE below:
1) DANGER! Turn the Switch OFF (o) and disconnect the Power Cord. Allow the Grill to
thoroughly cool if it is still hot. From beneath the Pellet Hopper, disconnect the Hot
Rod (Purple / White wire pair as shown in the wiring diagram near the end of this
manual). You will need to remove the Hopper Bottom Panel to access the wiring.
Once the Hot Rod is disconnected, replace the Hopper Bottom Panel and plug the
Power Cord back into an appropriate, grounded electrical outlet.
2) Open the Pellet Hopper and fill with TRAEGER BBQ PELLETS.
WARNING! USE ONLY TRAEGER BRAND BBQ WOOD PELLETS, which are
specifically made to work in our Grills. NEVER use heating fuel pellets in the
Grill due to potential hazardous contaminants and additives that may be
present.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Traeger Select Pro - BBQ400.03 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Traeger Select Pro - BBQ400.03 in the language / languages: English as an attachment in your email.

The manual is 1.04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info