798757
17
Zoom out
Zoom in
Previous page
1/23
Next page
need to be replaced. Contact your Traeger Dealer or the Traeger Parts Department
(Section Seven) to place an order.
c) If the fan blade turns a bit and then stops, continue watching and turn the Switch OFF
(o). If the fan blade UNWINDS slightly, this indicates a jam in the Auger system which will
need to be cleared.
d) DANGER! Turn the Switch OFF (o) and disconnect the Power Cord. Remove the
Pellets from the Pellet Hopper. Check for foreign objects and wet or decomposed Pellets,
both of which can cause a jam in the Auger system. The Auger will need to be removed to
clear a jam in the Auger system. See “HOW DO I REMOVE THE AUGER IF IT JAMS?”
section below.
`
HOW DO I REMOVE THE AUGER IF IT JAMS?
1) DANGER! Turn the Switch OFF (o) and disconnect the Power Cord.
2) CAUTION! If the Grill is still hot, allow it to thoroughly cool.
3) Remove any covers necessary to access the Auger Drive Motor.
4) Remove the screw connecting the Auger Drive Motor shaft to the Auger shaft and the
screw retaining the Auger Bushing into the Auger Tube.
5) With a small pipe wrench or locking pliers on the Auger shaft, turn the Auger counter
clockwise. It will turn hard until it breaks free, then the Auger will turn freely.
6) Remove the Auger and clean all Pellets, ash or foreign objects from the Auger, Auger Tube
and Firepot. (See instructions for proper handling and disposal of ash in Section
Five)
7) Sand the outside surfaces of the auger with medium grit sandpaper. Check the inside of the
Auger Tube and sand it if needed. Vacuum the sanding grit out of the Auger Tube and
Firepot when finished. Check that the Auger rotates freely.
9) Re-attach the Auger shaft to the Auger Drive Motor shaft.
WHY DOES MY GRILL FIRE GO OUT ON “SMOKE” SETTING?
The “P” number for the Smoke Adjustment on the Digital Control may be set too high.
Review the Digital Thermostat Control Functions in Section Four: Operating Tips to make
an adjustment.
There may be excess ash in the Firepot which needs to be cleaned.
WARNING! If the fire in the Firepot goes out while smoking, when sufficient Pellets are still
in the Pellet Hopper, it is important to follow these steps. Failure to do so may cause a
hazardous “over-firing” of your grill due to an excess of unburned pellets in the Firepot.
a) DANGER! Turn the Switch OFF (o) and disconnect the Power Cord. If the Grill is still
hot, allow it to thoroughly cool. Open the Door and remove all food, the Porcelain Grills,
Grease Drain Pan and the Heat Baffle.
b) WARNING! Remove all unburned pellets and ash from inside and around the Firepot.
(See instructions for proper handling and disposal of ash in Section Five)
c) Before replacing the Heat Baffle, Grease Drain Pan and the Porcelain Grills, plug the
Power Cord into an appropriate, grounded electrical outlet and turn the Switch ON (--).
Pellets should fall into the Firepot and the Hot Rod should begin to heat (it will start to turn
red). CAUTION! Do not touch it.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Traeger Bronson 20 - TFB29PLB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Traeger Bronson 20 - TFB29PLB in the language / languages: English as an attachment in your email.

The manual is 1.31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info