458423
32
Zoom out
Zoom in
Previous page
1/79
Next page
21
English Français
6
5
4
5
4
3
7
6
5
a
b
c
Adjusting thread tension
A good seam is formed when the tension is well
balanced and both threads (upper thread and lower
thread) are locked together in the center of the fabric.
After you finish sewing, check if the upper thread and
lower thread are equal.
Adjust the thread tension by turning the Upper Thread
Tension Dial.
a : Thread tensions are equal. Both threads are
locked in the center of the fabric.
b : Upper thread tension is too tight. Upper thread
lies straight along the surface of the fabric.
Correct the tension by turning the dial to a lower
number.
c : Upper thread tension is too loose.
Upper
thread lies straight along the reverse side of
fabric. Correct the tension by turning the dial to a
higher number.
Changing foot
1. Set needle to its highest position by rotating the
handwheel towards you.
Move presser foot lever to the middle position.
2. Raise foot release lever and remove foot. (fig A-1)
3. Place the desired foot on the needle plate under
the foot holder.
Lower the presser foot lever so that the foot snaps
on to the foot holder. (fig A-2)
Réglage de la tension du fil
Une bonne couture n’est possible que si la tension du
fil est bien réglée et que l’ensemble des fils supérieurs
et inférieurs sont serrer au centre du tissus.
Lorsque vous avez fini de coudre, vérifiez bien que la
tension du fil supérieur et inférieur est la même.
Régler la tension du fil en tournant le bouton de
tension du fil supérieur.
a : Les tensions des fils sont identiques.
L’ensemble des fils supérieurs et inférieurs sont
serrés au centre du tissu.
b : La tension du fil supérieur est trop forte. Le fil
supérieur se trouve à plat sur le tissu. Corriger la
tension en réglant le bouton de réglage de la
tension du fil sur un chiffre inférieur.
c : La tension du fil supérieur est trop faible.
Le
fil supérieur se trouve à plat sur le revers du tissu.
Corriger la tension en réglant le bouton de
réglage de la tension du fil sur un chiffre
supérieur.
Changement du pied-de-biche
1. Réglez l’aiguille à sa position la plus haute en
tournant le volant vers vous.
Libérer le pied-de-biche en relevant le levier
presseur de pied-de-biche à sa position centrale.
2. Levez le levier presseur de pied-de-biche et
l’enlever. (fig. A-1)
3. Placez le pied-de-biche désiré sur la plaque-
aiguille en dessous du support du pied.
Abaissez le levier de pied-de-biche de sorte que le
pied-de-biche tape sur le support du pied. (fig. A-2)
Quilt60_EFNI.book Page 21 Tuesday, July 12, 2005 8:01 PM
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toyota Quilt60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toyota Quilt60 in the language / languages: English, Dutch, French, Italian as an attachment in your email.

The manual is 4,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Toyota Quilt60

Toyota Quilt60 User Manual - German - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info