Manual Toyota Quilt50 (page 59 of 77) (English, Dutch, French, Italian)

458422

Zoom out

Zoom in

1/77

English Français

Making a buttonhole

1. Be sure that the declutch knob in the handwheel is

into the ( ) direction.

2. Measure the diameter and thickness of the button.

Add the thickness and 0.3 cm (for bar tacks) to

diameter. Mark the size of the buttonhole on the

fabric. (fig A)

❈ For stretch fabrics, lay a piece of paper where the

buttonhole will be placed.

3. Attach the Buttonhole Foot. Completely push back

the sliding part

of buttonhole foot. Place material

under foot so that the marking of buttonhole

passed through the center of foot. (fig B)

4. STEP 1 (front bar tack) (fig C)

Set pattern selection dial to No. 12

Set stitch length dial between 0.4-1

Lower the presser foot and sew 5-6 stitches. Step

the machine so the needle is at the left side of the

stitches. Raise needle.

5. STEP 2 (left side) (fig D)

Set pattern selection dial to No. 13

Sew left side from front to back until it reaches the

end of the marking. Stop the machine so the

needle is at the left side of the stitches. Raise

needle.

6. STEP 3 (back bar tack) (fig E)

Set pattern selection dial to No. 14

Sew 5-6 stitches. Stop the machine so the needle

is at the right side of the stitches. Raise needle.

7. STEP 4 (right side) (fig F)

Set pattern selection dial to No.15

Sew right side from back to front until it catches the

front bar tack. Stop the machine so the needle is at

the left side of the stitches. Raise needle and

presser foot.

8. Remove the fabric from the machine. Place a pin

through the bar tacks to prevent over-cutting. Cut

the center of the buttonhole with a ❈ Buttonhole

Cutter. (fig G)

❈ Included in accessories.

❈ Use buttonhole foot

Faire des boutonnières

1. Vérifier que le bouton de débrayage est bien

enclenché vers ( ).

2. Mesurer le diamètre et l’épaisseur du bouton.

Ajouter de l’épaisseur et 0,3 cm (pour le point

d’arrêt) au diamètre.

Marquer la taille de la boutonnière sur le tissu. (fig. A)

❈ Pour du stretch, placer un morceau de papier là où

la boutonnière sera placée.

3. Mettre en place le pied-de-biche boutonnière.

Passer à l’arrière la partie lisse

du pied-de-biche

boutonnière. Placer le tissu sous le pied-de-biche

de tel sorte que la marque effectué pour la

boutonnière passe par le centre du pied-de-biche.

(fig. B)

4. ETAPE 1 (point d’arrêt devant) (fig. C)

Régler le cadran sélecteur de point sur n° 12

Régler la longueur de point entre 0,4 - 1

Abaisser le pied-de-biche et coudre 5-6 points.

Arrêter la machine de tel sorte que l’aiguille du côté

gauche des points. Relever l’aiguille.

5. ETAPE 2 (côté gauche) (fig. D)

Régler le cadran sélecteur de point sur n° 13

Coudre d’avant en arrière jusqu’à ce qu’il atteigne la

fin du marquage. Arrêter la machine avec l’aiguille à

gauche. Relever l’aiguille.

6. ETAPE 3 (point d’arrêt à l’arrière) (fig. E)

Régler le cadran sélecteur de point sur n° 14

Coudre 5 à 6 points. Arrêter la machine avec

l’aiguille à droite des points. Relever l’aiguille.

7. ETAPE 4 (côté gauche) (fig. F)

Régler le cadran sélecteur de point sur n° 15

Coudre le côté droit, de l’arrière a l’avant jusqu’à ce

qu’il rejoigne le point d’arrêt de devant. Arrêter la

machine avec l’aiguille à gauche des points. Relever

l’aiguille et le pied-de-biche.

8. Enlever le tissu de la machine. Placer une épingle à

travers le point d’arrêt pour éviter des erreurs de

découpe. Couper le centre de la boutonnière avec

un coupe boutonnière. (fig. G)

❈ Inclus dans les accessoires.

0.3cm (1/8”)

0.4-1

A B

p1-end 05.1.11 0:51 PM ページ 47

I have posted a complaint which has been rejected because of spam - clever! Submitted on 13-2-2020 at 11:22
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Toyota Quilt50 in the language / languages: English, Dutch, French, Italian as an attachment in your email.

The manual is 2,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Toyota Quilt50

Toyota Quilt50 User Manual - German - 56 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Toyota Quilt50 Manual

Product: