458422
57
Zoom out
Zoom in
Previous page
1/77
Next page
45
English Français
Nederlands Italiano
Piecing Foot
1/4" Piecing Foot
Use the 1/4" piecing foot whenever a 1/4" seam
allowance is required.
A. Raise the foot release lever to remove the foot.
B. Place the piecing foot on the needle plate aligning
needle holes.
C. Lower the presser foot lever so that the ankle snaps
on the foot.
To stitch a 1/4" seam:
D. Align the edges of the fabrics with the right edge of
the presser foot.
E. When pivoting at a corner, stop when the fabric edge
is even with the front red line on the foot. Lower the
needle into the fabric and pivot. Continue to stitch.
To stitch a 1/8" seam:
F. Align the edges of the fabrics with the inside edge of
the right side of the presser foot.
G. When pivoting at a corner, stop when the fabric
edge is even with the middle red line on the foot.
Lower the needle into the fabric and pivot. Continue
to stitch.
Pied dapplication
Pied quart de pouce
Utilisez le pied quart de pouce toutes les fois ou une couture
quart de pouce est requise.
A. Poussez le levier de changement de pied-de-biche vers vous
et retirez le pied en place.
B. Mettre en place le pied dapplication sur la plaque aiguille puis
alignez les trous de la plaque avec celui du pied dapplication.
C. Abaissez le levier de pied-de-biche de manière à clipper le
pied sur son support.
Pour coudre une couture quart de pouce:
D. Alignez les bords du tissu avec le bord droit du pied-de-biche.
E. Lorsque vous parvenez au bord du tissu, stopper la couture
en prenant soin de vérifier que le bord du tissu soit en face de
la première ligne rouge du pied-de-biche. Piquez laiguille
dans le tissu, relevez le levier de pied-de-biche comme en C.
et tournez le tissu de 90˚, vous pouvez alors poursuive la
couture en point droit et répéter lopération à chaque angle.
Pour coudre une couture huitième de pouce:
F. Alignez les bords du tissu avec le bord intérieur droit du
pied-de-biche.
G. Pour négocier le passage des angles, lorsque vous arrivez
au bord du tissu, stopper la couture en alignant les bords du
tissu avec la 2
ème
ligne rouge (milieu) du pied-de-biche. Tout
en laissant laiguille plantée dans le tissu, faire pivoter
louvrage et continuez ainsi à coudre.
Verstelvoet
6mm Verstelvoet.
Gebruik de 6mm verstelvoet wanneer U een 6mm
naadomslag wilt.
A. Zet de persvoethendel omhoog zodat U het voetje kan
verwijderen.
B. Plaats de verstelvoet op de naaldplaat zodat de
naaldopening gelijk valt met die van de naaldplaat.
C. Zet de persvoethendel naar beneden zodat het pinnetje
in de houder klikt.
Het naaien van 6mm naad:
D. Plaats de kant van de stof gelijk aan de rechterkant van
de persvoet.
E. Wanneer U op een hoek wilt draaien, stop dan wanneer
de zijkant van de stof gelijk ligt met de voorste rode lijn
op het voetje. Plaats de naald in de stof en draai de
stof. Ga verder met naaien.
Het naaien van 3mm naad:
F. Plaats de kant van de stof gelijk aan de
rechterbinnenkant van de persvoet.
G. Wanneer U een hoek wilt draaien, stop dan wanneer
de zijkant van de Stof gelijk ligt met de middelste rode
lijn op het voetje. Plaats de naald in de stof en draai de
stof. Ga verder met naaien.
Piedino per patchwork
Piedino per patchwork con larghezza di 6 mm
Usate il piedino per patchwork da 6 mm quando avete
bisogno di questo tipo di cucitura.
A. Alzate la leva alza piedino per togliere il piedino.
B. Mettete il piedino per patchwork sulla placca ago
allineando i buchi dellago.
C. Abbassate la leva alza piedino cosicché il piedino si
agganci da solo.
Per cuciture da 6 mm di larghezza
D. Allineate i bordi del tessuto con il lato destro del
piedino.
E. Quando girate un angolo, fermatevi quando il bordo del
tessuto è pari con la linea rossa frontale del piedino.
Abbassate lago nel tessuto e girate. Continuate a
cucire.
Per cuciture di 3 mm di larghezza
F. Allineate i bordi del tessuto con il bordo interno del lato
destro del piedino.
G. Quando girate un angolo, fermatevi quando il bordo del
tessuto è pari con la linea rossa media del piedino.
Abbassate lago nel tessuto e girate. Continuate a
cucire.
BA C
D E
F G
p1-end 05.1.11 0:51 PM ページ 45
57


Need help? Post your question in this forum.

Forumrules
1

Forum

toyota-quilt50

Reset search

  • I have posted a complaint which has been rejected because of spam - clever! Submitted on 13-2-2020 at 11:22

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toyota Quilt50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toyota Quilt50 in the language / languages: English, Dutch, French, Italian as an attachment in your email.

The manual is 2,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Toyota Quilt50

Toyota Quilt50 User Manual - German - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info