603738

Toyota QUILT 226 Manual

53
Zoom out
Zoom in
Previous page
1/77
Next page
42
English Français
Nederlands Italiano
Walking Foot
This walking foot is used only with straight or zigzag stitch.
A. Name of parts
➀ Holder for needle clamp
➁ Holder for needle bar
B. • Rotate the handwheel toward you and raise the needle
to its highest position. And then turn off the power. Set
the pattern selecting dial: Straight stitch or zigzag stitch.
IMPORTANT: Make sure that the needle is at its
highest position when attaching the walking foot.
C. • Lift the presser foot lever to raise the presser foot.
• Loosen the screw of the presser foot holder by using
screw driver and remove the foot holder.
D. • Attach the holder
➀ to the needle clamp (A) and the
holder
➁ to the needle bar (B). And then tighten the
screw of the presser foot holder by using screw
driver.
• Lower the presser foot lifter and tighten the screw of
presser foot holder.
WARNING: To avoid injury, turn the handwheel slowly
toward you and make sure that the needle does not hit
the walking foot.
Pied-de-biche double entraînement
Ce pied-de-biche sera utilisé uniquement avec le point droit
et zig zag.
A. Désignation des éléments constitutifs du pied
➀ Support barre serre aiguille
➁ Support barre aiguille
B. • Amenez l’aiguille en position haute et coupez
l’alimentation électrique.
IMPORTANT: Assurez vous que l’aiguille est à sa
position la plus haute lors de l’opération de mise en
place du pied-de-biche double entraînement.
C. • Sélectionnez un point droit ou un zigzag sur le bouton
sèlecteur de points.
• Dévissez la vis de maintien du support de pied de biche
à l’aide du tournevis de plaque aiguille et ôtez le support.
D. • Attachez le support
➀ à la barre serre aiguille (A) et le
support
➁ à la barre aiguille (B).
• Abaissez le levier de pied-de-biche et vissez la vis de
fixation sur la barre aiguille.
ATTENTION: Pour éviter tout problème lié à cette
opération, tournez le volant vers vous mais lentement en
vous assurant que l’aiguille ne viennent pas taper sur le
pied-de-biche.
Piedino doppio trsporto
Il piedino doppio trasporto è stato ideato per rendere la
cucitura più semplice su alcuni tessuti, quali stoffa da
giacche, pelle, lana o jersey, rendendo così il trasporto più
sicuro e compatto.
A. Componenti
➀ Staffa per il morsetto dell’ago
➁ Leva per la barra ago
B. • Ruotare il volantino verso di voi e alzate l’ago nella
sua posizione più alta, e spegnete la macchina per
cucire.
C. • Sollevare la barra del piedino per alzare il piedino.
• Allentare la vite del gambo del piedino usando il
cacciavite in dotazione e rimuovere il gambo.
D. • Posizionate la staffa
➀ al morsetto ago (A) e la leva ➁
alla barra ago (B).
• Abbassate la leva alza piedino e stringete la vite della
staffa del piedino premistoffa.
ATTENZIONE: Per evitare danni, girate il volantino
lentamente verso di voi e assicuratevi che l’ago non
urti il piedino doppio trasporto.
Loopvoet
Deze loopvoet kunt U alleen gebruiken voor recht stikken
en de zigzagsteek.
A. Naam van het onderdeel:
➀ Houder voor de naaldklem.
➁ Houder voor de persvoetstang.
B. • Plaats de naald in zijn hoogste stand door aan het
handwiel te draaien en schakel daarna de machine uit.
BELANGRIJK: Wanneer U deze voet gaat gebruiken,
plaats U altijd de naald in zijn hoogste positie.
C. • Zet de persvoet omhoog doormiddel van de
persvoethendel.
• Draai de schroef van de persvoethouder los met de
naaldplaatschroevendraaier.
D. • Plaats de houder
➀ over de naaldklem (A) en de
houder
➁ aan de persvoetstang (B).
• Zet de persvoethefboom naar beneden en draai de
schroef voor de persvoethouder vast.
WAARSCHUWING: Controleer eerst, voordat U gaat
naaien, dat de naald niet de persvoet raakt anders
kunnen er ongelukken gebeuren. Dit doet U door het
handwiel langzaam naar U toe te draaien.
BA
DC
… 53 …


Need help? Post your question in this forum.

Forumrules
1

Forum

toyota-quilt-226

Reset search

  • Can you purchase a ruler foot for this machine and does the machine have a long or short shank Submitted on 7-5-2020 at 03:20

    Reply Report abuse

  • My stitch selector will only now do zigzag no matter what I do. It will not click and just goes round. I have taken the selector case off and have noticed a crack in the case shaft/shank. Is it possible to get a replacement? Submitted on 29-7-2018 at 17:16

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toyota QUILT 226 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toyota QUILT 226 in the language / languages: English, Dutch, French, Italian as an attachment in your email.

The manual is 2,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Toyota QUILT 226

Toyota QUILT 226 User Manual - German - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info