603717

Toyota EZ800 Manual

90
Zoom out
Zoom in
Previous page
1/115
Next page
English
Español
Français
75
AB
Changing the light bulb
Warning:
For your safety, always disconnect
the machine from power supply.
To prevent burns and electric
shocks, let the bulb cool down
before replacing it .
Bulbs can be purchased at your
nearest dealer.
(Always use 12V 5W model T10
bulbs)
A. • Ensure the machine is un
plugged and the light bulb is cool.
• Loosen the screw on the face
cover and remove the face cover
as shown in the illustration.
B. • Gently pull the bulb downward
to remove it.
• Insert a new bulb by pushing it
all the way to the top.
C. • Lower the presser foot pressure
rod.
D. • Insert the presser foot pressure
rod into the presser foot pressure
adjustment lever. Attach the face
cover.
E. Check if the presser foot pres-
sure adjustment lever moves
smoothly.
When it does not, remove the
face cover and follow the steps C
~ E again.
Reemplazo de la bombilla
ADVERTENCIA
Para su seguridad, desenchufe
siempre la máquina de la toma de
corriente de la pared.
Para evitar quemaduras y
descargas eléctricas, deje enfriar la
bombilla antes de reemplazarla.
Cualquier vendedor de máquinas de
coser de este tipo podrá
proporcionarle bombillas.
(Utilice siempre bombillas de 12V
5W del modelo T10)
A. • Asegúrese de que la maquina
está desenchufada y que la
bombilla está fría.
• Saque el tornillo de la tapa
lateral y quite la tapa como se
muestra en la ilustración.
B. • Tire despacio de la bombilla
hacia abajo para quitarla.
• Coloque una bombilla nueva
empujándola hacia arriba hasta
el tope.
C. • Baje la varilla de ajuste de la
presión del prensatelas.
D. • Introduzca la varilla en la
palanca de ajuste de la presión
del prensatelas. Coloque la tapa
lateral.
E. Compruebe que la palanca de
ajuste de la presión del
prensatelas se mueve
normalmente.
Si no es así, vuelva a quitar la
tapa lateral y vuelva a seguir las
instrucciones desde el punto tres
hasta al E.
Remplacement de l'ampoule
AVERTISSEMENT
Pour votre sécurité, débranchez
toujours la machine de la prise de
courant.
Pour éviter tout risque de brûlures
et de décharges électriques, laissez
l'ampoule refroidir avant de la
remplacer.
Vous pouvez vous procurer des
ampoules chez le revendeur le plus
proche.
(Utilisez toujours des ampoules T10
de 12V 5W)
A. • Assurez-vous que la machine
est débranchée et que l'ampoule
est froide.
• Desserrez la vis du panneau
latéral et enlevez-le comme
l'indique l'illustration.
B. • Tirez doucement sur l'ampoule
vers le bas pour l'enlever.
• Placez une ampoule neuve en
la poussant vers le haut jusqu'à
la butée.
C. • Baissez la tige du levier de
réglage de la pression du pied-
de-biche.
D. • Introduisez la tige dans le levier
de réglage de la pression du
pied-de-biche. Remettez le
panneau latéral en place.
E. Assurez-vous que le levier de
réglage de la pression du pied-
de-biche bouge sans a-coups.
Si ce n'est pas le cas, retirez le
panneau latéral et recommencez
les étapes C à E.
Ｐ７３－８２ 2006.08.04, 09:01Page 4 Ａｄｏｂｅ　ＰａｇｅＭａｋｅｒ　６．５Ｃ／ＰＰＣ
… 90 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toyota EZ800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toyota EZ800 in the language / languages: English, German, Dutch, French, Italian, Spanish, Spanish as an attachment in your email.

The manual is 2,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info