485654
19
Zoom out
Zoom in
Previous page
1/42
Next page
36
37
Operations
Connecting the power cord
1
Insert the power cord connector into
the AC IN socket of the projector.
2
Insert the power cord plug into a wall
or other power outlet.
Turning the power on
1
Remove the lens cap.
Remove the lens cap as shown (if present).
Be sure to remove the lens cap when the power is turned on.
If the cap is left on the projector, it could become deformed
due to heat.
2
Turn on the main power switch.
The ON/STANDBY indicator lights orange, and the
Status indicator lights green indicating standby mode.
3
Press the ON/STANDY button on
the control panel or on the remote
control.
The ON/STANDBY LED lights green and the internal
cooling fan starts.
4
After approximately 10 seconds,
the ON/STANDBY LED ashes
intermittently green.
5
The LAMP1 and LAMP2 LEDs light
green and the ON/STANDY LED
ashes more rapidly.
6
Once the ON/STANDBY, LAMP1 and LAMP2 LEDs are lit
solidly green, the projector is ready for use.
Turning the power on and off
Operations
Control panel
Remote
control
ON/STANDBY STATUS LAMP1 LAMP2
ON/STANDBY STATUS LAMP1 LAMP2
ON/STANDBY STATUS LAMP1 LAMP2
Power cord
connector
(supplied)
CAUTION
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyesight.
Do not block the air intake or exhaust. Doing so could cause a re due to internal overheating.
Do not place your hands, face, or other objects near the air exhaust, the lamp cover or the bottom of
the unit. Doing so could result in injury and/or damage.
Notes
The rst time you use the projector after purchase, after the start-up screen disappears,
the start menu is displayed.
When [Key lock] is [On], the operation buttons of the projector do not work
p.56
.
When [Password] is [On], enter password then the start-up screen is displayed after
the Password entry screen disappears
p.45
.
Do not touch the lens directly with your hand.
If ngerprints or stains are left on the projection lens surface, they may interfere with the
projector’s ability to project images on the screen.
Turning the power off
1
Press the ON/STANDBY button on the control panel or the
remote control.
A message appears on the screen, conrming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2
Press the ON/STANDBY button again.
The screen goes blank, but the internal cooling fan
continues to operate. Then, the projector goes into
standby mode.
During cooling, the ON/STANDBY indicator ashes. While the indicator is ashing, the
power can not be turned back on. However, there is no problem with unplugging the power
cord in this state.
Note
The projector consumes about 5W of power in standby. We recommend that you unplug
the power cord if you will not be using the projector for an extended period.
Precaution
If the power cord is unplugged before cooling is complete or the main power is turned
off, give the lamp time (about 5 minutes) to cool before plugging it back in. If the lamp
overheats, it may fail to light.
Power saving mode
Power saving mode activates the standby condition consuming less power than
Standard mode. Go to the Setting-Setting 2 menu to turn on Power saving mode.
ON/STANDBY STATUS LAMP1 LAMP2
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba TDP-WX5400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba TDP-WX5400 in the language / languages: English as an attachment in your email.

The manual is 7,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info