Manual Toshiba TDP-WX5400 (page 14 of 42) (English)

485654

Zoom out

Zoom in

1/42

Before UsingPreparationsOperationsMaintenanceOthers

TDP-WX5400

DATA PROJECTOR

OWNER’S MANUAL

Before Using

SAFETY PRECAUTIONS

The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to

alert the user to the presence of uninsulated "dangerous voltage" within the product's

enclosure that may be of sufcient magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle is intended to alert the user to

the presence of important operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT

INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO

QUALIFIED PERSONNEL ONLY.

WARNING:

USA only

Handling the cord on this product or cords associated with accessories sold with this

product, will expose you to lead, a chemical known to the State of California to cause

birth defects or other reproductive harm.

Wash hands after handling

WARNING:

USA only

Lamp contains mercury. Disposal of this product may be regulated due to

environmental considerations. For disposal, reuse or recycling information, please

contact your local government or the Electronic Industries Alliance at www.eiae.org.

MODEL NAME: TDP-WX5400

USA only

TRADE NAME: DATA PROJECTOR MODEL NAME: TDP-WX5400

Tested To Comply

With FCC Standards

FOR HOME OR OFFICE USE

FCC NOTICE: This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

Consult the dealer or an experienced radio/TV technician for help.

RESPONSIBLE PARTY:

TOSHIBA AMERICA INFORMATION SYSTEMS, INC.

9740 Irvine Blvd., Irvine, CA 92618-1697 U.S.A

Phone: (949) 583-3000

WARNING:

USA only

Changes or modications made to this equipment, not expressly approved by

Toshiba, or parties authorized by Toshiba, could void the user’s authority to operate

the equipment.

Notice:

CANADA only

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil

numérique de la classe B est conforme à la norme NMB-003 du Canada.

Before Using

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN

THIS OWNER'S MANUAL AND THOSE MARKED ON THE UNIT. RETAIN THIS

BOOKLET FOR FUTURE REFERENCE.

This unit is fully transistorized and does not contain any parts that can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS

VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

1. Read Owner’s Manual

After unpacking this product, read

the owner's manual carefully, and

follow all the operating and other

instructions.

2. Power Sources

This product should be operated

only from the type of power source

which does not exceed the voltage

range specied on the

rating label and

the power cord.

If you are not sure of the type of

power supply to your home, consult

your product dealer or local power

company.

3. Source of Light

Do not look into the lens while the

lamp is on. The strong light from

the lamp may cause damage to your

eyesight.

4. Ventilation

Openings in the cabinet are provided

for ventilation and to ensure reliable

operation of the product and to

protect it from overheating, and

these openings must not be blocked

or covered.

The openings should never be

blocked by placing the product

on a bed, sofa, rug or other similar

surface. This product should not be

placed in a built-in installation such

as a bookcase or rack unless proper

ventilation is provided.

5. Heat

The product should be situated away

from heat sources such as radiators,

heat registers, stoves, or other

products (including ampliers) that

produce heat.

6. Water and Moisture

Do not use this product near water.

- for example, near a bath tub, wash

bowl, kitchen sink, or laundry tub; in

a wet basement; or near a swimming

pool and the like.

7. Cleaning

Unplug this product from the wall

outlet before cleaning. Do not use

liquid cleaners or aerosol cleaners.

Use a soft cloth for cleaning.

8. Be sure that you firmly insert

the plug into the wall outlet.

Incorrect or faulty connections may

result in re or electric shock. Avoid

using an unsound or loose outlet.

9. Power-Cord Protection

Power-supply cords should be

routed so that they are not likely to

be walked on or pinched by items

placed upon or against them, paying

particular attention to cords at

plugs, convenience receptacles, and

the point where they exit from the

product.

10. Overloading

Do not overload wall outlets; to

reduce the risk of electric shock, do

not use the polarized plug with an

extension cord , receptacle, or other

outlet unless the blades can be

inserted completely with three-wire

grounding type to prevent blade

exposure. As this can result in a risk

of re or electric shock.

Before Using

IMPORTANT SAFETY INSTRUCTIONS (Continued)

11. Lightning storms

For added protection for this product

during storm, or when it is left

unattended and unused for long

periods of time, unplug it from the

wall outlet. This will prevent damage

to the product due to lightning and

power-line surges.

However, while it is thundering

or lightning, do not touch the

apparatus and any connected cable

and/or equipment.

This will prevent you from receiving

the electric shock by an electric

surge.

12. Object and Liquid Entry

Never push objects of any kind into

this product through openings as

they may touch dangerous voltage

points or short-out parts that could

result in a re or electric shock.

Never spill liquid of any kind on the

product.

13. Do not place or keep the

projector within the reach of

the children.

It may fall down or tip over, which

could result in severe injury.

14. Do not place the product

vertically

Do not use the product in the

upright position to project the

pictures at the ceiling, or any other

vertical positions. It may fall down

and dangerous.

15. Stack Inhibited

Do not stack other equipment on this

product or do not place this product

on the other equipment. Top and

bottom plates of this product

develops heat and may give some

undesirable damage to other unit.

16. Moving the projector

When carrying the projector, be sure

to use the carrying handle to avoid

any damage to the lens or main unit.

17. Attachments

Do not use attachments not

recommended by product

manufacturer as they may cause

hazards.

18. Accessories

Do not place this product on an

unstable cart, stand, tripod, bracket,

or table. The product may fall,

causing serious injury to a child

or adult, and serious damage to

the product. A product and cart

combination should be moved with

care. Quick stops, excessive force,

and uneven surfaces may cause the

product and cart combination to

overturn.

S3125A

19. Damage Requiring Service

Unplug this product from the

wall outlet and refer servicing to

qualified service personnel under the

following conditions:

a) When the power-supply cord or plug

is damaged.

b) If liquid has been spilled, or objects

have fallen into the product.

c) If the product has been exposed to

rain or water.

d) If the product does not operate

normally by following the operating

instructions. Adjust only those

controls that are covered by

the operating instructions as an

improper adjustment of other

controls may result in damage and

will often require extensive work by

a qualied technician to restore the

product to its normal operation.

e) If the product has been dropped or

damaged in any way (If the cabinet

should break, please handle with

care to avoid injury) .

f) When the product exhibits a distinct

change in performance - this

indicates a need for service.

Before Using

IMPORTANT SAFETY INSTRUCTIONS (Continued)

20. If glass components, including

lens and lamp, should break,

contact your dealer for repair

service.

This product incorporates glass

components, including a lens and

a lamp. If such parts should break,

please handle with care to avoid

injury and contact your dealer for

repair service. The broken pieces

of glass may cause to injury. In the

unlikely event of the lamp rupturing,

thoroughly clean the area around

the projector and discard any edible

items placed in that area.

21. Servicing

Do not attempt to service this

product yourself as opening or

removing covers may expose you to

dangerous voltage or other hazards.

Refer all servicing to qualified service

personnel.

22. Replacement Parts

When replacement parts are

required, be sure the service

technician has used replacement

parts specied by the manufacturer

or have the same characteristics as

the original part.

Unauthorized substitutions may

result in re, electric shock, or

other hazards.

23. Safety Check

Upon completion of any service

or repairs to this product, ask the

service technician to perform safety

checks to determine that the product

is in proper operating condition.

24. Do not leave thermal-paper

documents or easily deformed

items on top of the unit or

near the air exhaust for long

periods of time.

The heat from the unit could erase

the information on the thermal

paper, or cause deformation or

warping.

25. Do not use the product in a

closed installation state.

Do not place the product in a box

or in any other closed installation

state. Otherwise it may overheat. This

could result in a risk of re.

POWER SUPPLY INFORMATION

If your line voltage is 220 to 240V, use one of the following types of cable/plug.

Plug

configuration

Plug type

Australian

240V

10A

North American

240V

15A

Switzerland

240V

Line voltage

EURO

220 – 240V

200 – 240V

Plug

configuration

Plug type Line voltage

Use a 5A fuse which is approved by ASTA

or BSI to BSI362.

Always replace the fuse cover after

changing the fuse.

IMPORTANT PRECAUTIONS

Moisture Condensation

Never operate this unit immediately after moving it from a cold location to a warm location.

When the unit is exposed to such a change in temperature, moisture may condense on the lens

and the crucial internal parts. To prevent the unit from possible damage, do not use the unit for

at least 2 hours when there is an extreme or sudden change in temperature.

Place and Manner of Installation

Do not place in hot locations, such as near heating equipment. Doing so could cause

malfunction, and shorten the life of the projector.

Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts, shortening

their lives, and darkening the screen.

Do not use this product in the upright position or tilt it up or down by more than 20° from

level. Doing so may cause a failure or shorten the life of the product.

Using this instrument near a TV or radio may cause interference to the images or audio

sound. If this happens, move it away from the TV or radio.

In a high altitude location where air is thin, cooling efciency is reduced so use the

projector with [Fan mode] set to [High].

p.58

Only plug the power cord into outlets rated for use with the power cord’s specied voltage

range. Do not overload extension cords or table taps as this can result in re or electric

shock.

Route the power cable or the connecting cable away from where people could trip over it.

The projector may fall down, which could result in severe injury.

Be sure the power cord is easily reached for unplugging in case of emergency. Do not

place any obstacles near a wall outlet in which the cord is plugged.

•

Before Using

IMPORTANT PRECAUTIONS (Continued)

Avoid Volatile Liquid

Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or plastic

products touching the unit for a long time. They will leave marks on the nish.

Do not use a chemically saturated cloth.

EXEMPTION CLAUSES

Toshiba Corporation bears no responsibility in the case of damages arising from natural

disaster such as earthquakes, lightning, etc., re not liable to Toshiba Corporation, acts

by third parties, other accidents, or use under abnormal conditions including erroneous or

improper operation and other problems.

Toshiba Corporation bears no responsibility for incidental damages (lost prot, work

interruption, corruption or loss of the memory contents, etc.) arising from the use of or the

inability to use this unit.

Toshiba Corporation accepts no liability whatsoever for any damages arising from not

having followed the descriptions in this Instruction Manual.

Toshiba Corporation accepts no liability whatsoever for any damages arising from

malfunctions arising from combination with equipment or software that is not related to

Toshiba Corporation.

•

In the spaces provided below, record the Model and Serial No. located at the bottom of your

projector.

Model No.

Serial No.

Retain this information for future reference.

OTHER INFORMATION

Copyrights

Showing or transmitting commercial imaging software or broadcast or cable-broad casting

programs with the purpose of other than the personal and private viewing, including

modifying images using the freeze function, or displaying with the varying aspect ratio

of the images, could violate the direct or indirect copyrights of the imaging software or

broadcast program, etc., if done without rst consulting with the copyright holder. For this

reason, please take appropriate measures before performing one of the actions listed

above, including obtaining a license from the copyright holder.

Disposal

This product contains substances which are harmful to humans and the environment.

The lamp contains mercury.

Please dispose of this product or used lamps in accordance with local regulations.

Following information is only for EU-member states:

The use of the symbol indicates that this product may not be treated as

household waste. By ensuring this product is disposed of correctly, you will

help prevent potential negative consequences for the environment and human

health, which could otherwise be caused by inappropriate waste handling of

this product. For more detailed information about recycling of this product,

please contact your local city ofce, your household waste disposal service or

the shop where you purchased the product.

Trademarks

VGA, SVGA, XGA, SXGA, UXGA, and WXGA are trademarks or registered trademarks

of International Business Machines Corporation.

DLP

(Digital Light Processing) is a registered trademark of Texas Instruments, Inc.

Macintosh is a registered trademark of Apple Computer, Inc.

Windows is a registered trademark of Microsoft Corporation in the U.S. and other

countries.

Adobe is a registered trademark and Acrobat Reader is a trademark of Adobe Systems

Incorporated.

All other brand and product names are trademarks or registered trademarks of their

respective companies.

Notational Conventions Used in This Manual

References to pages with related information are annotated as follows.

For example, if making a reference to page 36:

p.36

The illustrations in this document are for reference purposes only and may not reect

your package exactly.

•

Caution

Never throw batteries into a re.

Using the batteries improperly may cause them to explode or leak and lead to burn or

injury. If battery-leaking uid contacts skin, wash the uid off immediately with clean water

and consult a doctor. If the uid is spilt on an instrument, avoid contact and wipe it off using

tissue paper. (Dispose of the used tissue paper as ammable garbage after moistening

with water.)

Notes

Be sure to use AAA (LR03) size batteries.

Dispose of batteries in a designated disposal area.

Attention should be drawn to the environmental aspects of battery disposal.

Do not mix different battery types or combine used batteries with new ones.

If the remote control does not operate correctly, or if the operating range becomes

reduced, replace both batteries with new ones.

If the batteries are dead or if you will not be using the remote control for a long time,

remove the batteries to prevent battery acid from leaking into the battery compartment.

Following information is only for EU-member states:

[Disposal of batteries and/or accumulators]

The crossed out wheeled dust bin symbol indicates that batteries

and/or accumulators must be collected and disposed of separately from

household waste.

If the battery or accumulator contains more than the specied values

of lead (Pb), mercury (Hg), and/or cadmium (Cd) dened in the Battery

Directive (2006/66/EC), then the chemical symbols for lead (Pb),

mercury (Hg) and/or cadmium (Cd) will appear below the crossed out

wheeled dust bin symbol.

By participating in separate collection of batteries, you will help to

assure the proper disposal of products and batteries and thus help

to prevent potential negative consequences for the environment and

human health.

For more detailed information about the collection and recycling

programmes available in your country, please contact your local city

ofce or the shop where you purchased the product.

•

Hg Cd Pb

•

REMOTE CONTROL BATTERIES

Before Using

CONTENTS

Before Using

SAFETY PRECAUTIONS ............................................................................. 2

IMPORTANT SAFETY INSTRUCTIONS ......................................................4

POWER SUPPLY INFORMATION ............................................................... 9

IMPORTANT PRECAUTIONS ......................................................................9

EXEMPTION CLAUSES ............................................................................. 10

OTHER INFORMATION ............................................................................. 11

REMOTE CONTROL BATTERIES ............................................................. 12

CONTENTS ................................................................................................ 14

Preparations

Checking the package contents ..................................................................16

Introduction to the projector ........................................................................ 17

Features you will enjoy: ........................................................................... 17

Names of each part on the main unit .......................................................... 18

Carrying the projector .................................................................................. 19

Names of each part on the control panel and remote control ..................... 20

Names of the connector panel terminals ..................................................... 22

Preparing and using the remote control ...................................................... 23

Operating a computer using the remote control .......................................... 24

Placement ................................................................................................... 25

Projection distance and size ....................................................................... 26

Connection ..................................................................................................28

Installing or removing the projection lens .................................................... 30

Removing the lens from the projector ...................................................... 30

Installing the new lens ............................................................................. 31

Securing the lens using the anti-theft screw ............................................ 32

Installing the optional color wheel (provided) ..............................................32

Storing unused color wheel ..................................................................... 34

Operations

Turning the power on and off ...................................................................... 36

Basic operations .......................................................................................... 38

Using handy features .................................................................................. 42

Using auto setting (computer input only) ................................................. 42

Correcting the keystone distortion ........................................................... 42

Cutting off the picture and sound temporarily (Mute) ............................... 43

Changing picture mode ............................................................................ 43

Changing screen size .............................................................................. 43

Freezing the image (Freeze) ................................................................... 44

Setting the password ............................................................................... 44

Menu tree ....................................................................................................46

Using the Adjust menus ............................................................................. 50

The Image adjustment menu ...................................................................50

The Display setting menu ........................................................................ 53

The Advanced menu ................................................................................ 54

Using the Setting menus .............................................................................55

The Setting 1 menu ................................................................................. 55

The Setting 2 menu ................................................................................. 56

The Setting 3 menu ................................................................................. 58

Using the Status display screen ..................................................................59

The Usage time screen ............................................................................ 59

The Input screen ......................................................................................59

The Network screen ................................................................................. 60

The Version screen .................................................................................. 60

Operation using an HTTP browser .............................................................. 61

Overview ..................................................................................................61

Preparation before use ............................................................................ 61

Handling of the address for operation by using a browser ...................... 61

Conguring network settings ................................................................... 62

Structure of the HTTP Server .................................................................. 63

Maintenance

About the lamps .......................................................................................... 64

Replacing the lamps .................................................................................... 65

Resetting the lamp hours counter ............................................................68

Lens and main unit cleaning ....................................................................... 70

Cleaning the lters ...................................................................................7

Replacing the lters ..................................................................................... 72

Resetting the lter time counter ...............................................................73

Others

Trouble indications ......................................................................................74

ON/STANDY LED ....................................................................................74

Status LED ............................................................................................... 74

Lamp LEDs ..............................................................................................74

Before calling service personnel ................................................................. 75

Specications ..............................................................................................76

Screen Trigger .........................................................................................80

Preparations

Checking the package contents

Preparations

Please make sure that the following items are included in the box, along with the main unit. If any

item is missing, immediately contact the store where you purchased the product.

(1) (4) (7)

(2) (5) (8)

(3) (6)

(1) Remote control

(2) LR03 (SIZE AAA) batteries for remote control (2)

(3) CD-ROM

(4)

Owner’s Manual

(5)

RGB cable (1.8m)

(see note 1)

(6)

Power cord

(see note 1,2)

(7)

Six segment color wheel

(8)

Lens anti-theft screw

Note

1. To maintain original performance, always use the supplied cables.

2. The shape and number of supplied power cords vary depending on the product destination.

Save Original Packing Materials

The original shipping carton and packing materials will come in handy if you ever have to ship

your projector. For maximum protection when shipping your projector, repack the set as it was

originally packed at the factory.

The Supplied CD-ROM



The supplied CD-ROM contains an owner’s manual in Portable Document Format (PDF).

Please use Acrobat Reader 5 or later version to view the manual.

Adobe

Acrobat

Reader

or Adobe

Reader

The supplied CD-ROM does not contain Acrobat

Reader

. If you cannot read PDF les,

please install Adobe Reader software in your computer by downloading it from Adobe

Systems website.

Viewing the Manual

Run the CD-ROM and double-click on Start.pdf. Acrobat

Reader

launches, and the menu

screen of the owner’s manual appears. Click on your language. The Owner’s Manual cover

and list of bookmarks appears. Click on a bookmark title to view that section of the manual.

Click on

to view a reference page with related information.

See the Help menu for more information about Acrobat

Reader



Introduction to the projector

Features you will enjoy:

•

DLP projector with high resolution

•

Native WXGA support

A WXGA (1280 x 800) resolution provides wide screen display with an aspect ratio of 15:9.

•

High brightness

igh brightness output of 5200 and 4500 lumens is achieved using the 4-segment color

wheel.

•

Dual Lamp system

wo-lamp system offers increased lamp life and energy savings along with redundancy.

•

Extensive projection lens with bayonet mount

•

Powered Lens Shift, Zoom, and Focus offer installation exibility

Powered Horizontal and Vertical lens shift provides the ability to project from off center

screen installations. Powered zoom and focus provide quick and easy adjustment.

•

Direct Power Off & Auto Start

The projector has a feature called “Direct Power Off”. This feature allows the projector

to be turned off (even when projecting an image) using a power strip equipped with a

switch and a breaker.

Note

• Before using Direct Power Off, be sure to allow at least 20 minutes right after turning

on the projector and before starting to display an image. Also, the power cable can be

removed immediately after turning off the projector. Auto Start eliminates the need to

always turn off the projector by the ON/STANDBY button on the remote control or projector

cabinet.

•

A variety of input ports and a comprehensive array of system control interfaces

This projector supports input signals including BNC, DVI-D, analog RGB, component,

S-video, and composite.

•

3W+3W Stereo speakers

Built in 3W x 2 speakers are provided.

•

Prevent unauthorized use of the projector

nhanced smart security settings for password protection, cabinet control panel lock to

help prevent unauthorized access, adjustments and theft deterrence.

•

Integrated RJ-45 connector for wired networking capability for property management

•

Combination of BrilliantColor™ and 6-segment color wheel offers true color reproduction



Preparations

Names of each part on the main unit

(1) (2) (3) (4)

(7)(8)

(5)(6) (10)(9) (11) (12) (14) (15) (16)(13) (17)

Front Back

Name : Function

(1) Lamp cover :

Remove to replace lamp.

p.65

(2) Lens : Remove lens cap before use.

(3) Control panel :

Operates the projector.

p.20

(4) Speaker :

Outputs audio sound.

(5) Front IR Receiver :

Receives IR signals from the remote control.

p.23

(6) Lens release button : Press the release button before removing the lens.

(7) Intake vent and front lter :

Keeps the front fan free of dust.

•

Clean regularly for optimum performance.

•

Do not obstruct.

(8) Anti-theft screw : Prevents theft of the lens.

(9) Foot adjuster :

Adjusts level of projector.

p.39

(

) Right lter :

Keeps the right fan free of dust.

•

Clean regularly for optimum performance.

•

Do not obstruct.

(

) Connector panel :

Connect various input devices.

p.22

(

) Rear IR Receiver :

Receives IR signals from the remote control.

p.23

(

) Rear lter :

Keeps the rear fan free of dust.

•

Clean regularly for optimum performance.

•

Do not obstruct.

(

) Air exhaust : Expels air that has grown hot inside the projector—do not

obstruct.

(

) Kensington lock : Attach the projector to a permanent object with the

Kensington slot and a security cable.

(

) Security chain lock : Attach the projector to a permanent object using a security

cable.

(

) Carrying handle : Pull up the handle when carrying the projector.

Carrying the projector

Always carry your projector by the handle.

Before moving or carrying the projector, disconnect the power cable and any other cables that

may be attached to it.

When moving the projector or when the projector is not in use, cover the lens with the lens cap.

To extend the projector handle, refer to the following guide.

Stand the projector on its end with the panel terminal facing to the bottom.

Note

Stand the projector on its end by lifting the cabinet. Do not use the handle to place the

projector upright.

Lift the handle in the direction shown until it is fully extended.

•

20 21

Preparations

Names of each part on the control panel and remote control

(1)

(2)

(6)

(7)

(3)

(4)(8)

(6)

(7)(20)

(21)

(8)

(5)

(2)

(3)

(4)

(5)

(18)

(19)

(9)

(22)

(23)

(24)

(10)

(11)

(12)

(10)(25)

(11)(26)

(12)

(15)

(16)

(17)

(13)

(13)(27)

(28)

(14)

(15)

(16)

(17)

(14)

(18)

(19)

Remote ControlControl panel

Name : Main Function

Control panel

(1)

ZOOM + button

Adjusts the screen size.

(2)

ZOOM – button

Adjusts the screen size.

(3)

UP SHIFT button

Move images up.

(4)

RIGHT SHIFT button : Move images right.

(5)

DOWN SHIFT button :

Move images down.

(6)

FOCUS + button :

Focus the projected image.

p.39

(7)

FOCUS – button

Focus the projected image.

p.39

(8)

LEFT SHIFT button

: Move images left.

(9)

MENU button

Displays menus.

p.46

(10) Selection button

Menu selections and adjustments, volume control, etc.

p.46

(11) RETURN button

: Goes back one screen.

(12) AUTOSET button :

Performs auto-adjustment of input signals from computer.

p.42

(13) LAMP 2 :

See Indicator Messages.

p.74

(14) LAMP 1

See Indicator Messages.

p.74

(15) ENTER button

Accepts the selected mode.

(16)

ON/STANDBY button

Turns the power on/off (standby).

p.36

Name : Main Function

(17) INPUT button :

Selects input.

p.38

(18) ON/STANDBY (LED) : See Indicator Messages.

p.74

(19) STATUS (LED) : See Indicator Messages.

p.74

Remote control

(1) Status LED : Lights when the remote control is used.

(2) ON/STANDBY button :

Turns the power on/off (standby).

p.36

(3) INPUT button :

Selects input.

p.38

(4)

Cursor control button (Right)

Controls a Cursor.

p.24

(5) Page Dn button : Proceeds PowerPoint® slides.

p.24

(6) ENTER button : Executes menu operations, etc.

(7) Selection button (Right) : Menu selections and adjustments, volume control, etc.

p.46

(8) FOCUS + button :

Focus the projected image.

p.39

(9) FOCUS – button :

Focus the projected image.

p.39

(10) AUTOSET button :

Performs auto-adjustment of input signals from computer.

p.42

(11) Vol + button : Ajusts the volume.

(12) STATUS button : Opens the OSD Status menu (the menu only opens when

an input device is detected).

(13) Vol – button : Ajusts the volume.

(14) Cursor control button (Up): Controls a Cursor.

p.24

(15) ENTER button : Accepts the selected mode.

(16) Cursor control button (Left): Controls a Cursor.

p.24

(17)

Cursor control button (Down)

Controls a Cursor.

p.24

(18) Page Up button : Reviews PowerPoint® slides.

p.24

(19) Selection button (Up) :

Menu selections and adjustments, volume control, etc.

p.46

(20) Selection button (Left) :

Menu selections and adjustments, volume control, etc.

p.46

(21) Selection button (Down) :

Menu selections and adjustments, volume control, etc.

p.46

(22) ZOOM + button : Adjusts the screen size.

(23) ZOOM – button : Adjusts the screen size.

(24) RETURN button : Goes back one screen.

(25) MENU button :

Displays menus

p.46

(26) MUTE button : Cuts off the picture and sound temporarily.

p.43

(27) FREEZE button : Pauses image.

p.44

(28) LENS SHIFT button : Displays the lens shit screen.

p.39

Note

For the remainder of this manual, buttons are referred to as follows:

Selection buttons

⇒

pqtu

; ENTER button

⇒

•

Preparations

Names of the connector panel terminals

(11)(12)(13)(14)(15)(16)(19) (18)(17)

(8)(6) (7)(5)(4)(3) (10)(9)(2)(1)

Name : Main Function

(1) COMPUTER 1 IN : Connect a VGA cable from a computer.

(2) LAN : Connect a LAN cable from a computer.

(3) USB :

Connect the USB cable from a computer for rmware

upgrades or keypad remote emulation.

(4) AUDIO IN (1) : Connect the audio cable from the input device.

(5) COMPUTER 3 IN :

Connect the DVI cable from a computer.

(6) AUDIO IN (3) : Connect the audio cable from the input device.

(7)

AUDIO OUT

: Audio loop through.

(8) MONITOR OUT : Connect a monitor.

(9)

AUDIO IN (2)

: Connect the audio cable from the input device.

(

) RS232C terminal :

When operating the projector via a computer, connect this

to the controlling computer’s RS-232C port

p.79

(

) SCREEN TRIGGER : When connected to the screen through a commercially

available cable, the screen deploys automatically on

start up of the projector. The screen retracts when the

projector is powered off.

p.80

(

) Main power switch : Turn on/off the projector.

(

) S-VIDEO : Connect a commercially available S-video cable from a video

device.

(

) L/MONO, R

(Component)

: Connect an RCA audio cables from the input device right and

left channels.

(

) AC IN : Connect the supplied power cable.

(

) L/MONO, R (Video) : Connect RCA audio cables from the input device right and

left channels.

This audio jack is shared with S-Video input.

(

) VIDEO IN : Connect a composite video cable from a video device to the

yellow RCA jack.

(

) COMPONENT IN

(Y, Cb/Pb, Cr/Pr)

: Connect a component video enabled device.

(

) COMPUTER 2 IN

(R/PR, G/Y, B/PB, H, V)

: Connect RGBHV or Component signal from computer or

component video enabled device.

Loading dry-cell

batteries

into the remote control

Remove the battery cover.

Insert the dry-cell batteries.

Be sure to align the plus and minus ends of

the batteries properly.

Two batteries (LR03, SIZE AAA) are used.

Replace the battery cover.



Operating the remote

control

Point toward the projector’s infrared

remote sensor, and press a button

on the remote control.

Operating the projector from the front

Approx. 15°

Approx. 7m

Note

The above operation is also applicable

for the remote control operation from

rear side.

•



•

Dry-cell batteries

Before using the batteries, be sure to observe the Safety Precautions described in previous pages.

If the remote control stops working, or if its range decreases, replace all the batteries with new

ones. (2 batteries (LR03 SIZE AAA))

Do not heat, take apart, or throw batteries into re.

Do not use new and old batteries together, or different types of batteries together.

Dispose of used batteries according to local regulations.

Remove batteries from remote control when not using for extended periods.

Keep the batteries away from the reach of children.

Batteries are choking hazards and can be very dangerous if swallowed. If the batteries are

swallowed, seek medical assistance immediately.

The remote control

Avoid exposing the remote control infrared sensor to bright sunlight or uorescent lighting.

Do not drop or bang.

Do not leave in hot or humid locations.

Do not allow it to get wet or place it on top of wet objects.

Do not take it apart.

Ensure that the battery polarities (+/–) are aligned correctly.

In rare cases, ambient conditions could impede the operation of the remote control. If this

happens, point the remote control at the main unit again, and repeat the operation.

•

Preparing and using the remote control

Preparations

Operating a computer using the remote control

A computer can be operated using the projector’s remote control. This function is available

on any computer with the Windows

98/98SE, Windows

Me, Windows

2000, Windows

XP, or

Windows Vista

operating system, that is equipped with a USB port which can support USB1.1 (This

function is also supported on OS 9 or MAC OS X for the Macintosh). However, please note that

Toshiba does not guarantee the operation of all computers.

Connecting a computer

Connect a USB cable (not supplied) from the projector to a computer.

To USB port

Operating a computer

Operate remote control’s buttons towards the projector’s IR receiver.

Moving the cursor

Press the keyboard function buttons (cursor control buttons) in the direction you wish the

cursor to move.

Using the computer’s page up [

] and down [

] function

Press the Page Up and Page Dn buttons to switch PowerPoint

slides.



Placement Styles

As shown in the gures below, this device can be placed in 4 different styles.

The factory setting is “oor-mounted front projection.” Set [Projection mode] in the

Setting - Setting 2 menu

p.56

, in accordance with your needs.

Floor-mounted front projection

Floor-mounted rear projection

Ceiling-mounted front projection

Ceiling-mounted rear projection

WARNING

Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing

the unit. Attempting to clean and replace the lamp in a high location by yourself may cause

you to fall, resulting in injury.

If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so.

Mounting the projector on a ceiling requires special ceiling brackets (sold separately) and

specialized knowledge. Improper mounting could cause the projector to fall, resulting in

possible injury and unit damage.

If the projector is ceiling-mounted, install the breaker for turning off the power in case of

anomaly. Let everyone involved with the use of the projector know that fact.

•

Placement

26 27

Preparations

Use the gures and tables below to determine the projection size and projection distance.

(Projection sizes are approximate values for full-size picture with no keystone adjustment).

is the distance between the lens and the screen.

Example of TLPNL54:

The further your projector is away from the screen or wall, the larger the image becomes. The minimum

size the image is approximately 40 inches (1.02 m) measured diagonally when the projector is in the

distance of 60.2 inches (1.53 m) from the wall or screen. The largest the image can be is 500 inches

(12.70 m) when the projector is in the distance of 754.7 inches (19.17 m) from the wall or screen.

Lens

Screen Size

TLPSFL54 TLPSL54 TLPNL54

Diagonal Width Height (B)

Distance (A)

WIDE TELE WIDE TELE WIDE TELE

[inches] [m] [inches] [m] [inches] [m] [inches] [m] [inches] [m] [inches] [m] [inches] [m] [inches] [m] [inches] [m]

40 1.02 33.9 0.86 21.3 0.54 - - - - 45.3 1.15 60.6 1.54 60.2 1.53 79.5 2.02

50 1.27 42.6 1.08 26.4 0.67 32.7 0.83 - - 56.3 1.43 76.0 1.93 75.6 1.92 99.6 2.53

60 1.52 50.9 1.29 31.9 0.81 39.4 1 - - 67.7 1.72 90.9 2.31 90.6 2.3 119.7 3.04

80 2.03 67.8 1.72 42.6 1.08 52.4 1.33 - - 90.2 2.29 121.3 3.08 120.9 3.07 159.4 4.05

100 2.54 84.8 2.15 53.2 1.35 65.7 1.67 - - 112.6 2.86 152.0 3.86 150.8 3.83 199.2 5.06

120 3.05 101.7 2.58 63.9 1.62 78.7 2 - - 135.4 3.44 182.3 4.63 181.1 4.6 239.0 6.07

150 3.81 127.3 3.23 79.6 2.02 98.4 2.5 - - 169.3 4.3 227.6 5.78 226.4 5.75 298.8 7.59

180 4.57 153.0 3.88 95.4 2.42 118.1 3 - - 203.1 5.16 273.2 6.94 271.7 6.9 358.7 9.11

200 5.08 170.0 4.31 106.0 2.69 131.1 3.33 - - 225.6 5.73 303.5 7.71 302.0 7.67 398.4 10.12

300 7.62 254.7 6.46 159.4 4.04 - - - - 338.2 8.59 455.5 11.57 452.8 11.5 598.0 15.19

400 10.16 339.8 8.62 212.2 5.38 - - - - 451.2 11.46 607.1 15.42 603.9 15.34 797.2 20.25

500 12.70 424.6 10.77 265.5 6.73 - - - - 563.8 14.32 759.1 19.28 754.7 19.17 996.5 25.31

Projection distance and size

(Reference: TLPNL54)

1.53 m

1.02 m

1.27 m

1.52 m

2.03 m

2.54 m

1.92 m 2.3 m 3.07 m 3.83 m

Lens

Screen Size

TLPML54 TLPLL54

Diagonal Width Height (B)

Distance (A)

WIDE TELE WIDE TELE

[inches] [m] [inches] [m] [inches] [m] [inches] [m] [inches] [m] [inches] [m] [inches] [m]

40 1.02 33.9 0.86 21.3 0.54 75.2 1.91 150.4 3.82 150.4 3.82 281.5 7.15

50 1.27 42.6 1.08 26.4 0.67 94.1 2.39 187.8 4.77 187.8 4.77 352.0 8.94

60 1.52 50.9 1.29 31.9 0.81 113.0 2.87 225.6 5.73 225.6 5.73 422.4 10.73

80 2.03 67.8 1.72 42.6 1.08 150.8 3.83 300.4 7.63 300.4 7.63 563.0 14.3

100 2.54 84.8 2.15 53.2 1.35 188.2 4.78 375.6 9.54 375.6 9.54 703.9 17.88

120 3.05 101.7 2.58 63.9 1.62 226.0 5.74 450.8 11.45 450.8 11.45 844.5 21.45

150 3.81 127.3 3.23 79.6 2.02 282.3 7.17 563.4 14.31 563.4 14.31 1055.9 26.82

180 4.57 153.0 3.88 95.4 2.42 339.0 8.61 676.4 17.18 676.4 17.18 1266.9 32.18

200 5.08 170.0 4.31 106.0 2.69 376.4 9.56 751.2 19.08 751.2 19.08 1407.9 35.76

300 7.62 254.7 6.46 159.4 4.04 565.0 14.35 1127.2 28.63 1127.2 28.63 2111.4 53.63

400 10.16 339.8 8.62 212.2 5.38 753.1 19.13 1502.8 38.17 1502.8 38.17 2815.4 71.51

500 12.70 424.6 10.77 265.5 6.73 941.3 23.91 1878.3 47.71 1878.3 47.71 3519.3 89.39

For your reference, the throw distance can be also obtained by the following formulas.

Throw Distance

Lens [Inches] [Meters]

TLPSFL54

[Notes 1]

B × 0.817 - 1.535 B × 0.817 - 0.039

TLPSL54 B × 1.379 - 1.969 through B × 1.854 - 1.811 B × 1.379 - 0.050 through B × 1.854 - 0.046

TLPNL54 B × 1.844 - 2.362 through B × 2.435 - 2.48 B × 1.844 - 0.060 through B × 2.435 - 0.063

TLPML54 B × 2.328 - 4.134 through B × 4.639 - 4.173 B × 2.328 - 0.105 through B × 4.639 - 0.106

TLPLL54 B × 4.580 - 5.433 through B × 8.604 - 5.354 B × 4.580 - 0.138 through B × 8.604 - 0.136

* “B” means the screen width.

Notes

TLPSFL54 is guaranteed the performance only when the Lens Shift is set to 0%. Ensure

to adjust the Lens Shift

p.39

as the Lens center comes at the Screen center shown in

the gure on

p.25

•

28 29

Preparations

Connection

Before connection

Read the owner’s manual of the device you are connecting to the projector.

Some computers cannot be used or connected to this projector.

Check for an RGB output terminal and supported signal

p.78

Turn off the power of both devices before connecting.

•

Notes

The COMPUTER 1 IN terminal functions identically to the COMPUTER 2 and 3 IN

terminals.

The MONITOR OUT connector will output no video signal (Digital signal) from the

COMPUTER 3 IN connector. If no input is selected, the MONITOR OUT terminal

outputs the input signals last selected for each input terminal.

Signals are output from MONITOR OUT terminal even in standby mode.

However, from AUDIO OUT terminal, no audio signal is output.

A computer monitor cannot accept Y/P

B/PR signals correctly.

The AUDIO IN 1, 2, and 3 terminals double for devices connected to COMPUTER

terminals 1, 2, and 3.

When an AUDIO OUT terminal is connected, sound is not output from the projector

speaker.

Output volume of AUDIO OUT terminal can be adjusted by the VOL button.

•

30 31

Preparations

CAUTION:

Do not shake or apply excessive pressure on the projector or the lens components as

the projector and lens components contain precision parts.

When shipping the projector with the projection lens, remove the projection lens before

shipping the projector. Improper handling during transportation may cause damage to

the lens and the lens shift mechanism.

Before removing or installing the lens, be sure to turn off the projector, wait until the cooling

fans stop, and turn off the main power switch.

Do not touch the lens surface when removing or installing the lens.

Keep ngerprints, dust or oil off the lens surface. Do not scratch the lens surface.

Work on a level surface with a soft cloth under it to avoid scratching.

If you remove and store the lens, attach the cap to the projector to keep off dust and

dirt.

Do not turn on the projector when a projection lens is not mounted.

•

Removing the lens from the projector

Remove the lens cap.

Push the LENS RELEASE button all the way in and rotate the lens counterclockwise.

The lens will be disengaged.

Note

If the lens cannot be removed by using the LENS RELEASE button, the anti-theft screw may be

in use to secure the lens. If that is the case, remove the anti-theft screw rst.



•

Installing or removing the projection lens

Pull out the lens slowly.

CAUTION:

When Installing the projection lens into the projector, be sure to remove the lens cap

from the back of the lens before installing into the projector. Failure to do so will cause

damage to the projector.

•

Installing the new lens

Insert the lens with the arrow mark of the unit facing up.

Rotate the lens clockwise until you feel it click into place.



Arrow Mark

Preparations

Securing the lens using the anti-theft screw

Using the anti-theft screw to prevent theft of the lens. Tighten the supplied anti-theft screw

on the front bottom.

Installing the optional color wheel (provided)

This projector comes with a four-segment color wheel installed. An additional six-segment color

wheel is also provided. To replace the color wheel (located under the lamp cover adjacent to

lamp 1) refer to the following guide.

Note

Wait until the lamp housing and the color wheel cool off.

Loosen the captive screw (A) on the lamp cover.

Remove the lamp cover by sliding it in the direction of the arrow (B).



•

Anti-theft screw hole

for lens unit

Anti-theft screw

Unscrew the retaining screws (x 4) on the four-segment color wheel.

Lift the color wheel in the direction shown.

Insert the six-segment color wheel.

Installing or removing the projection lens (Continued)

Secure the retaining screws as shown.

Align the lamp cover in the direction of the arrow (A) and slide it into place.

Secure the captive screw (B).

Storing unused color wheel

Keep the unused color wheel in the zipper bag in which the 6-segment color wheel was

packaged.

This bag prevents dust from falling or collecting on the color wheel.



Installing or removing the projection lens (Continued)

Operations

Connecting the power cord

Insert the power cord connector into

the AC IN socket of the projector.

Insert the power cord plug into a wall

or other power outlet.

Turning the power on

Remove the lens cap.

Remove the lens cap as shown (if present).

Be sure to remove the lens cap when the power is turned on.

If the cap is left on the projector, it could become deformed

due to heat.

Turn on the main power switch.

The ON/STANDBY indicator lights orange, and the

Status indicator lights green indicating standby mode.

Press the ON/STANDY button on

the control panel or on the remote

control.

The ON/STANDBY LED lights green and the internal

cooling fan starts.

After approximately 10 seconds,

the ON/STANDBY LED ashes

intermittently green.

The LAMP1 and LAMP2 LEDs light

green and the ON/STANDY LED

ashes more rapidly.

Once the ON/STANDBY, LAMP1 and LAMP2 LEDs are lit

solidly green, the projector is ready for use.



Turning the power on and off

Operations

Control panel

Remote

control

ON/STANDBY STATUS LAMP1 LAMP2

Power cord

connector

(supplied)

CAUTION

Do not look into the lens while the lamp is on. The strong light from the lamp may cause

damage to your eyesight.

Do not block the air intake or exhaust. Doing so could cause a re due to internal overheating.

Do not place your hands, face, or other objects near the air exhaust, the lamp cover or the bottom of

the unit. Doing so could result in injury and/or damage.

•

Notes

The rst time you use the projector after purchase, after the start-up screen disappears,

the start menu is displayed.

When [Key lock] is [On], the operation buttons of the projector do not work

p.56

When [Password] is [On], enter password then the start-up screen is displayed after

the Password entry screen disappears

p.45

Do not touch the lens directly with your hand.

If ngerprints or stains are left on the projection lens surface, they may interfere with the

projector’s ability to project images on the screen.

Turning the power off

Press the ON/STANDBY button on the control panel or the

remote control.

A message appears on the screen, conrming that you wish to shut off the power. This

message will disappear after a moment. (This operation is no longer valid after the

message disappears.)

Press the ON/STANDBY button again.

The screen goes blank, but the internal cooling fan

continues to operate. Then, the projector goes into

standby mode.

During cooling, the ON/STANDBY indicator ashes. While the indicator is ashing, the

power can not be turned back on. However, there is no problem with unplugging the power

cord in this state.

Note

The projector consumes about 5W of power in standby. We recommend that you unplug

the power cord if you will not be using the projector for an extended period.

Precaution

If the power cord is unplugged before cooling is complete or the main power is turned

off, give the lamp time (about 5 minutes) to cool before plugging it back in. If the lamp

overheats, it may fail to light.

Power saving mode

Power saving mode activates the standby condition consuming less power than

Standard mode. Go to the Setting-Setting 2 menu to turn on Power saving mode.

•



•



ON/STANDBY STATUS LAMP1 LAMP2

Operations

Basic operations

Turn on the power.

Turn on the power by following the instructions in “Turning the power on”

p.36

Select the language (When using the rst time).

When the projector is used for the rst time after purchase, the start menu for language

selection is displayed in English. (If the screen is out of focus, adjust it according to the step 6.)

Use the

button to select the desired language and press the

button.

Message for setup conrmation is displayed in a selected language.

Notes

When the projector is turned on the next time, the start menu does not appear upon

startup. However, if [All data] is executed from the Reset menu, the start menu will

be displayed the next time when the power is turned on.

The language can also be set from the Setting-Setting 1 menu

p.51

This owner’s manual assumes that English has been selected.

Activate the connected device.

Turn on and start the connected device such as a computer.

Press the INPUT button.

An image of the connected equipment is projected.

Each time you press the INPUT button, it switches to the input of the connected equipment

that is outputting video signals.

•

Projector placement angle adjustments

The placement angle and the height of the projected image can be adjusted by the

foot adjusters.

To raise the level of the projector, twist

the adjusters clockwise.

To lower the level of the projector, lift

the projector and twist the adjusters

counter clockwise.

Adjusting zoom and focus

If you wish to adjust the screen size,

use the ZOOM buttons on the projector

or remote to adjust the screen size.

Use the FOCUS buttons on the

projector or remote to adjust the focus.

Adjusting the Picture Position and

Picture Size

The Picture Position and Picture Size can be adjusted manually from the lens control panel

or from the remote control unit (LENS SHIFT button)

Adjusting Picture Position and Picture

Size Manually

Press the Select keypad in any

direction to bring up the [Lens Shift]

window.

Press the directional key as required

to shift the image. Releasing the

directional arrow will re-center the

cursor.

Operations

To alter the picture size,

press Menu and select the

[Adjust] menu using

. Press Enter to open the

[Adjust] menu. Press

to select [Display setting]

followed by

to select

[Screen]. Press Enter.

The [Screen] window is

displayed. Select the desired

picture size using

and press Enter.

When nished, press

[Return] to go back to the

projected image.

Adjusting the volume

The volume can be adjusted with the

remote control unit.

Press the Vol +/- buttons

on the remote control. The

volume bar is displayed on

screen.

Use the Vol +/- buttons to adjust the level.

Notes

Volume can also be adjusted from the Volume in the Menu.

•

Basic operations (Continued)

Notes

Note that lamp characteristics may rarely cause the brightness to uctuate slightly.

A lamp is consumable item. If used for extended periods, images will appear dark, and the

lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime of

the lamp depends on conditions of use.)

The DLP

chip is made using extremely advanced technology, but there may be black spots

(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Please

note that these are not malfunctions.

Although this projector supports a wide range of RGB signals

p.78

, any resolutions not

supported by this projector (WXGA) will be expanded or shrunk, which will affect image

quality slightly. To view high-quality images, it is recommended that the computer’s

external output should be set to WXGA resolution.

With some models of computer having LCD displays or the like, displaying images

simultaneously on the projector and the monitor’s display may prevent the images from

displaying properly. If this happens, turn off the computer’s LCD display. For information on

how to turn off the LCD display, see the owner’s manual of your computer.

If no signal is being input from the connected equipment or signal input is stopped while

projecting, the “No signal” will appear.

If a signal not supported by the projector is input, “No signal” message will appear.

If an unavailable operation button is pressed, “This function is not supported” will appear.

•

42 43

Operations

Using handy features

Using auto setting (computer input only)

This function automatically sets up the projector to the optimum state. It sets up the

sampling phase, frequency and screen position, etc., for each type of input signal

through a simple operation.

Press the AUTOSET button.

Notes

The image may not be projected or auto adjustment/setting may

not be performed correctly for input signals other than those

supported by the projector

p.78

If auto setting fails adjustment, adjust manually through Adjust,

Display setting menu

p.53

Correcting the keystone distortion

When the projector placement angle against the screen is changed while projecting

the image, the picture will undergo keystone (trapezoidal) distortion. This projector is

capable of correcting this keystone distortion.

Before correction

After correction

Adjusting Keystone distortion

Select the Setting menu using

. Press Enter to open the Setting

menu. Press

to select Setting

1 followed by

to select

Keystone. Press Enter.

Use the

buttons to adjust the keystone distortion.

Notes

Depending on the amount of keystone adjustment needed and the image content,

some information may be lost, or the picture quality may suffer.

The keystone correction settings are memorized after the power has been turned

off—the projector placement angle against the screen remains unchanged.

Some adjustments using keystone correction while displaying an input image with

a 16:9 aspect ratio, may affect displaying the menu properly. In such a case, reset

keystone correction to use the menu.



•



•

Remote

control

Cutting off the picture and sound temporarily (Mute)

When you want to project the images of another projector, overhead

projector, etc. temporarily, this projector’s images and sound can be

turned off.

Press the remote control’s MUTE button.

The picture and sound are cut off. (The Mute function is released

when pressing the MUTE button again.)

Notes

Operating any other functions will also cancel the muting.

The mute function is supported during most video and audio

playback.

Precaution

Do not replace the lens cap to cut off the projected image temporarily. It may cause

the lens cap to deform due to the heat.

Changing picture mode

The projected image mode can be selected.

Select the Adjust menu using

. Press Enter to open the Adjust

menu. Press

to select Image adjustment followed by

select Picture mode. Press Enter.

Press

to select the desired mode and press Enter.

Changing screen size

The screen size for the projected image can be changed.

Select the Adjust menu using

. Press Enter to open the Adjust

menu. Press

to select Display setting followed by

to select

Screen. Press Enter.

Press

to select the desired mode and press Enter.

Notes

Thru display is available for Computer and Network-input images.

Wide display is available for Y/P

B/PR, Video and S-video-input images.

Using this function on commercial video software, broadcast or cable-broadcasting

except for the purpose of your private viewing and listening may infringe the



•



•

Remote

control

Operations

Freezing the image (Freeze)

This function is used to pause or freeze a video during a presentation.

Press the remote control’s FREEZE button.

The picture will pause. To release the freeze function, press the

FREEZE button again.

Notes

Other operations will also release the freeze.

Even if an image is frozen on the projector, the pictures are

running on the video or other equipment.

Using this function on commercial video software, broadcast or cable-

broadcasting except for the purpose of your private viewing and

listening may infringe the copyright protected by the copyright laws.

Setting the password

How to set password (from [Off] to [On])

To set the security password, refer to the

following guide.

Press the Menu button on the projector

or remote control to display the Main

Menu. Scroll to the [Setting] menu using

and press Enter.

Select [Setting 2] using

and

press Enter.

Select [Password]

using

and

press Enter.

Select [On] then [OK] and press

Enter.

The password entry screen is displayed.

Enter a password between 4 and 10

characters using the arrow keys of

the remote control. Press Enter.

Re-enter the password for

conrmation and press Enter.

Select [OK] using the remote control and

press Enter to enable the password.

Note

Please do not forget your password. If you forget the password, you can not release the

password by yourself.

In such a case, please contact your dealer.

•



•



Remote

control

How to operate when password is [On]

Turn on the power.

The lamp lights and the password entry screen appears.

Enter the password using the arrow keys of the remote control.

If the entered password is correct, the start-up screen appears and the projector

goes into normal operation. If the password is wrong, a message will appear

prompting you to re-enter the password, and the password entry screen is displayed

again. If you enter an incorrect password for more than 5 times, the projector will

automatically power off and enter standby mode.

Note

When the password setting is [On], the password will be enabled only when the

power is turned on for the rst time after the main power switch has been on.

The password function will not be activated if the power backed on while it is

standby mode without turning off the main power switch.

How to set password (from [On] to [Off])

Select [Password] in the

[Setting 2] menu and press

Enter.

The password entry screen is

displayed.

Enter the password using

the arrow keys of the remote

control.

Select [Off] and press Enter

to disable the password.

•

Using handy features (Continued)

Operations

Menu tree

Top menu

Input

Adjust Computer1

Volume

Setting

Status display

Computer2

Computer3

Y/PB/PR

Video

S-Video

Adjust

Image adjustment

Display setting

Advanced

Setting

Setting 1

Setting 2

Setting 3

Status display

Usage Time

Input

Network

Version

Reset

Current signal

All data

Clear lamp1 time

Clear lamp2 time

Clear filter time

0~61

Adjust

Setting 1

Gamma

Color temp

BrilliantColor

Dynamic/Natural/Black Detail

5000K/6500K/7800K/8500K

/9300K/10500K

1~3

White

balance

R-level

G-level

B-level

0~100

Image

Adjustment

Picture mode

Detail settings

Contrast

Brightness

Sarpness

Color

Tint

Bright/Presentation/Video/Cinema/Photographic/sRGB

Setting 1/White balance/Color correction

0~100

0~31

0~100

Reset

Display

setting

Screen

Overscan

Position adjustment

H-position

V-position

Frequency

Phase

4:3/16:9/16:10/Letterbox/True/Standard

93%/95%/97%/100%

+\- 50

+\- 25

+\- 50

0~63

Mode priority Wide/4:3

Advanced

Noise reduction

3D Y/C separation

Progressive

Color matrix

Off/Low/Mid/High

Off/On

Off/Still/Standard/Cinema

Auto/RGB/SDTV/HDTV

Off/2-2/2-3 Auto/2-2/2-3

Film

0~100

Color

correction

Yellow

Magenta

Cyan

-60~60

Operations

Menu tree (Continued)

Setting

Setting 1

Keystone

Lamp power

Lamp mode

Lamp interval

Language

Lens Shift

Zoom

H-keystone (-100~100)

V-keystone (-100~100)

Low/Standard*

Dual*/Lamp1/Lamp2

Off*/1 week/4 week/2000H

English/Deutsch/Francais/Italiano/Espanol/

Svenska/

Focus

Network

setting

DHCP

IP address

Subnet

Gateway

DNS

Enable*/Disable

Apply settings

Projection mode

Display time

Background

Password

Key lock

DynamicBlack

RC sensor

Standard*/Rear ceiling/

Rear/Ceiling

Continuous/5 sec/15 sec/

45 sec*

Off*/On

Blue/None*/Logo

Off*/On

Both*/Front/Back

Network setting

Standby mode

Standard*/Power-saving

PC control PC control*/Network

Setting 3

Power on

No signal power off

Screen trigger

FAN mode

Manual/Auto

Off*/5 min/10 min/20 min/30 min

Off*/On

Standard*/High

Default input select

Last source*/Auto/Computer1/Computer2/Computer3/Y/PB/PR/Video/S-Video

Video mode

Video

Auto*/NTSC/PAL/SECAM

S-Video Auto*/NTSC/PAL/SECAM

Message Off/On*

Filter warning

Off/100[H]/200[H]/500[H]*/1000[H]

Standard*/FineSearch mode

Setting 2

Status

display

Version

Model name

Firmware

Usage

time

Lamp1

Lamp2

Lamp1 time

Lamp2 time

PJ time

Filter time

Network

IP address

Subnet

Gateway

MAC address

Input

Input name

Signal

H-sync. freq

V-sync. freq

Video mode

Sync

Sync polarity

Scan type

Operations

The Adjust menu contains overall projector settings for image output such as sharpness, overscan

and color matrix. Three tabs are accessible through the Adjust menu; Image adjustment, Display

setting, and Advanced.

Items that can be set or adjusted are marked “Yes”, and those that cannot are marked “No”. (When

an item is masked, it indicates that you cannot select for the current input).

The Image adjustment menu

Item

Description

Computer 1 Computer 2 Computer 3

Y/PB/PR

Video

S-video

Picture mode

Press

and toggle the picture

mode with

Bright/Presentation/Video/

Cinema/Photographic/sRGB

Yes Yes Yes Yes Yes Yes

Contrast

Adjust the image contrast.

Lower

Higher

Yes Yes Yes Yes Yes Yes

Brightness

Adjust the brightness of the image.

Darker

Lighter

Yes Yes Yes Yes Yes Yes

Sharpness

Adjust the sharpness of the image.

Softer

Sharper

Yes Yes Yes Yes Yes No

Color

Adjust the color of the image.

Lighter

Deeper

No No No Yes Yes No

Tint

Adjust the tint of the image color.

Reddish

Greenish

No No No Yes Yes No

*1: Tint can be displayed and adjusted only when the video signal is set to [NTSC] or [Auto].



Using the Adjust menus

The Setting 1 menu

Item

Description

Bright

Presenatation

Video

Cinema

Photographic

sRGB

Gamma

Press

and toggle the Gamma

level with

Dynamic/Natural/Black detail

Yes Yes Yes Yes Yes Yes

Color temp.

Adjust the Color temp.

Lower

Higher

No No Yes Yes Yes Yes

BrilliantColor

Adjust the BrilliantColor value.

Lower

Higher

No No Yes Yes Yes Yes

The White balance menu

Item

Description

Bright

Presenatation

Video

Cinema

Photographic

sRGB

R-level Adjust the R-level.

Lower

Higher

Yes Yes Yes Yes Yes Yes

G-level Adjust the G-level.

Lower

Higher

Yes Yes Yes Yes Yes Yes

B-level Adjust the B-level.

Lower

Higher

Yes Yes Yes Yes Yes Yes

Operations

The Color correction menu

Item

Description

Bright

Presenatation

Video

Cinema

Photographic

sRGB

Yellow

Adjust the Y level. Lower

Higher

No Yes Yes Yes Yes Yes

Magenta

Adjust the M level. Lower

Higher

No Yes Yes Yes Yes Yes

Cyan

Adjust the C level. Lower

Higher

No Yes Yes Yes Yes Yes

Using the Adjust menus (Continued)

The Display setting menu

Item

Description

Computer 1 Computer 2 Computer 3

Y/PB/PR

Video

S-video

Screen

Select the screen size using

4:3 —

Atandard TV screen.

16:9 — Wide screen aspect for

video output.

16:10 — For video signal with an

aspect ratio of 16:10

Letterbox — For viewing LaserDisc

movies or non-

anamorphic DVDs on a

16:9 screen

True —

Displays the image in its

true resolution.

Standard —

Displays the image in its

aspect ratio.

Yes Yes Yes Yes Yes Yes

Overscan

Select the overscan value with

93%/95%/97%/100%

Yes Yes Yes Yes Yes Yes

H-position Adjust the horizontal position of the

image.

Move left

Move right

Yes Yes No Yes No No

V-position Adjust the vertical position of the

image.

Move down

Move up

Yes Yes No Yes No No

Frequency Adjust with

to eliminate periodic

patterns and ickering when ne

vertical lines appear on the screen.

Yes Yes No Yes No No

Phase

Adjust to eliminate icker with

Yes Yes No Yes No No

Mode priority Enable or disable mode priority

override with

Wide/4:3

Yes Yes Yes No No No

Notes

If you use the Screen setting function on commercial video software, broadcast or cable-

broadcasting programs to display images with the varying aspect ratio except for the purpose

of your private viewing and listening, it may infringe the copyright protected by the copyright

laws.

[Mode priority] allows you to set the signals which are difcult to distinguish between

[Wide] or [4:3] to your selected mode.



•

54 55

Operations

The Advanced menu

Item

Description

Computer 1 Computer 2 Computer 3

Y/PB/PR

Video

S-video

Noise

reduction

Adjust the screen noise

reduction level.

Off/Low/Mid/High

Yes Yes Yes Yes Yes Yes

3D Y/C

separation

Enbale or disable 3D Y/C

separation.

On/Off

No No No No Yes No

Progressive Adjust the progressive mode.

Off/Still/Standard/Cinema

No No No Yes Yes Yes

Color matrix Set the default Color matrix.

Auto/RGB/SDTV/HDTV

Yes Yes Yes Yes No No

Film Set the Film mode.

Off/2-2/2-3 Auto/2-2/2-3

No No No Yes Yes Yes

*1: Noise reduction may not work depending on signal type.



Using the Adjust menus (Continued)

Using the Setting menus

The Setting menu contain the most often used settings during installation and options

to customize the general output of the projector. Three tabs are accessible through the

Setting menu; Setting 1, Setting 2, and Setting 3.

The Setting 1 menu

Item

Description

Keystone

Adjust the horizontal/vertical keystone values. Press

and adjust the keystone using

Lamp power

Set the lamp power. Press

and select the lamp power using

Low/Standard

Lamp mode

Set the lamp mode. Press

and select the lamp mode using

Dual/Lamp1/Lamp2

Lamp interval Set the period of time after which the lamp should be swapped when lamp select is not set

to Dual mode. Press

and select the lamp interval using

Off/1 week/4 week/2000H

Language Select one of the languages below to use for displaying the menu and messages

Press

and toggle the display language using

/ / / / / / /

中文

(

簡體字

)

Lens Shift Shift the lens using the projector's control panel.

•

Press

to display the Len shift window.

•

Press

to shift the lens in the corresponding direction.

Zoom

Use the Zoom feature from the projector's control panel.

•

Press

to display the Zoom window.

•

Press

to zoom out and

to zoom in.

Focus

Use the Focus feature from the projector's control panel.

•

Press

to display the Focus window.

•

Adjust the focus by pressing

and

Notes

For lamp protection, [Lamp mode] cannot be changed its setting mode right after you

have switched the lamp mode or the lamp has turned on. If it is the case, allow some

time before changing the mode.



•

Operations

The Setting 2 menu

Item

Description

Projection

mode

Set the projection mode. Press

and select the projection mode using

•

Standard—standard forward facing projection.

•

Rear ceiling—inverts and reverses the image for ceiling mounted projection from behind the screen.

•

Rear—reverses the image for projection from behind the screen.

•

Ceiling—inverts the image for standard ceiling mounted projection.

Display time

Set the menu display time. Press

and select the display time using

Continuous/5 sec./15 sec./45 sec.

Background

Set the default background appearance. Press

and select the background using

Blue/None/Logo

Password

Enable or disable the password security feature

p.45

Key lock Enable or disable the key lock security feature. When enabled, the control panel on the

projector is locked—the menus can only be accessed using the remote control.

Press

and select On or Off using

DynamicBlack Enable or disable DynamicBlack. The DynamicBlack feature improves the appearance of black

areas of the projected image. Press

and select On or Off using

RC sensor

Enable or disable the front and reaer remote control sensors. Press and select the

sensor mode using

Both/Front/Rear.

Network

setting

Congure the network settings if the projector is connected to a network. Enable DHCP or

disable DHCP and enter network IP address information in the supplied elds.

Select Apply settings to conrm the network information

p.57

Standby mode

Select the desired standby mode. Press and select the standby mode using

Standard/Power-saving

PC control

Select the path for PC Control. Press and select the PC control path using

PC control/Network



Using the Setting menus (Continued)

Network settings

<DHCP>

If you set DHCP to Enable, the IP address of the projector is assigned automatically

by the DHCP server. If your network environment does not assign IP addresses

automatically, set DHCP to Disable, then set the following items manually.

Note

IP address and Subnet are required elds if DHCP is set to Disable.

When DHCP is set to Disable, consult with your network administrator for the settings

below and set the IP address manually.

An IP address is a unique number assigned to a device. The format is a string of four dot-

separated three-digit numbers. (Example: 111.112.xxx.xxx)

A subnet mask is used to determine what subnet the IP address assigned to a device belongs to.

(Example: 255.255.xxx.xxx)

This value specifies the IP address of the device, such as a router, to be used to access servers

outside the network. (Example: 111.112.xxx.xxx)

<DNS>

This value species the IP address of a Domain Name Server (DNS) if present.

(Example: 111.112.xxx.xxx)

Select Apply settings to conrm the projector’s new network settings.

•

58 59

Operations

The Setting 3 menu

Item

Description

Power on

Select the power on mode. Press and select the power on mode using

Manual—the projector must be powered on manually using the control panel or remote.

Auto—the projector powers on automatically when the main power switch is turned on.

No signal

power off

Sets the time to wait for the power to be turned off after the last operation is made with

no input signal. Press

and select the lamp interval using

Off/5 min./10 min./20 min./30 min.

Screen trigger

Enable or disable the screen trigger function. Press and select On or Off using

Fan mode

Select the desired fan mode. Press and select the fan mode using

Standard/High

Default input

select

Select the image source that the projector will search for automatically on startup. Press

and select the default input device using

Last source/Auto./Computer1/Computer2/Computer3/Y-PB-PR/Video/S-video

Video mode

Video: Press and select the default video mode using

Auto./NTSC/PAL/SECAM

S-video: Press

and select the default S-video mode using

Auto./NTSC/PAL/SECAM

Message

Enable or disable the onscreen warning and informational messages. Press and select On

or Off using

Filter warning

Set the interval between lter cleaning warning messages. Press and select the desired

interval using

Off/100H/200H/500H/1000H

Search mode

Set the search mode. Press and select the desired search mode using

Standard/Fine

Note

If [Power on] is set to [Auto] and there is a power outage, the projector will come on

once power is restored.

Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise

gets louder.) Set this option to use the projector, for example, at high altitude (over 1,200

meters above sea level).

Do not set Fan mode to [High] when using the projector at a lower altitude.”



•

Using the Setting menus (Continued)

The Status display screen provides a quick access to the detailed information on projector status.

The Status display menu contains four distinct tabs; Usage time, Input, Network, and Version.

Note

Information on the Status display screens is read only.

The Usage time screen

Item

Description

Lamp1 Displays the Lamp1 life remaining as a percentage.

Lamp2 Displays the Lamp2 life remaining as a percentage.

Lamp1 time Displays the Lamp1 total usage in hours.

Lamp2 time Displays the Lamp2 total usage in hours.

PJ time Displays the projector's total usage in hours.

Filter time Displays the lter total usage in hours.

Note

Displays [Lamp 1/2 time] as a measure of when the lamp should be replaced. (Cannot be

used as a counter of guaranteed lamp time.) When the displayed time approaches 2,000

hours, consult with a dealer about getting replacement for:

TLPLW25 for TDP-WX5400 (sold separately).

The Input screen

Item

Description

Input name Displays the input terminal that is currently being used.

Signal Displays the signal name of the currently being used.

H-sync. freq. Displays horizontal frequency in KHz

V-sync. freq. Displays vertical frequency in Hz

Video mode Displays video type, if present.

Sync Displays synchronization type.

Sync polarity Displays sychronization polarity.

Scan type Displays the scan type.

•



Using the Status display screen

60 61

Operations

The Network screen

Item

Description

IP address Displays the IP address associated with the projector, if connected to a network.

Subnet Displays the subnet mask associated with the projector, if connected to a network.

Gateway Displays the gateway associated with the projector, if connected to a network.

MAC address Displays the MAC address associated with the projector.

The Version screen

Item

Description

Model name Displays the projector's model name.

Firmware Displays the rmware version currently running on the projector.

Note

Firmware shows the version of the projector’s internal control program. This rmware

version will be requested for customer service purposes.

Note

The displayed information will not be refreshed if the status changes. To refresh the

information, dismiss the display, then display it again.



•

Using the Status display screen (Continued)

Operation using an HTTP browser

Overview

The use of HTTP server functions will allow control of the projector from a web browser

without the installation of special software. Please be sure to use “Microsoft Internet

Explorer 4.x” or a higher version for the web browser. (This device uses “JavaScript” and

“Cookies” and the browser should be set to accept these functions. The setting method

will vary depending on the version of browser. Please refer to the help les and the other

information provided in your software).

HTTP server functions is available by accessing the following URL. Enter the either

address below in the browser address bar.

http:// <the projector’s IP address> /index.html

http:// <the projector’s IP address> /lanconf.html

Note

The display or button responses can be slow or operation may not be accepted

depending on your network settings. Should this happen, consult your network

administrator. The projector may not respond if its buttons are repeatedly pressed in

rapid intervals. Should this happen, wait a moment and repeat. If you still can’t get any

response, turn off and back on the projector.

Preparation before use

Make network connections, set up the projector and conrm that it is complete before

engaging in browser operations.

Operation with a browser that uses a proxy server may not be possible depending on the

type of proxy server and the setting method. Although the type of proxy server will be a

factor, it is possible that items that have actually been set will not be displayed depending

on the effectiveness of the cache, and the contents set from the browser may not be

reected in operation. It is recommended that you do not use a proxy server unless it is

inevitable.

Handling of the address for operation by using a

browser

Regarding the actual address that is entered for the address or entered to the URL address

bar when operation of the projector is via a browser, the host name can be used as it is

when the host name corresponding to the IP address of the projector has been registered

to the domain name server by a network administrator, or the host name corresponding

to the IP address of the projector has been set in the “HOSTS” le of the computer being

used.

Example 1:

When the IP address of the projector is 192.168.73.1, access is gained to the HTTP server functions

by specifying http://192.168.73.1/index.html for the address or the entry column of the URL



•



Operations

Conguring network settings

The Network Settings screen is displayed as follows:

http:// <the projector’s IP address> /lanconf.html

DOMAIN

Host Name: Type in a hostname. Up to 60 alphanumeric characters can be used.

Domain Name: Type in domain name of the network connected to the projector. Up to 60

alphanumeric characters can be used.

Apply: Click to reect the entries.

MAIL

Alert Mail: Click Enable to enable Alert Mail feature. This option noties your computer

of an error message via e-mail when using wired LAN. The error message will be notied

when the projector lamp has reached the end of its usable life or an error occurs in the

projector.

Sender’s Address: Specify the sender’s address. Up to 60 alphanumeric characters can be used.

SMTP Server Name: Type in the SMTP server name to be connected to the projector. Up to 60

alphanumeric characters can be used.

Recipient’s Address 1 to 3: Type in recipient addresses. Up to 60 alphanumeric characters can be used.

Apply: Click to apply the settings.

TEST MAIL

Send a test mail to check if your settings are correct. Click to Execute to enable this

feature.

Test Mail Status Button: Click to display the test result.

Sample of a message sent from the projector:

Projector Name: X X X X

Lamp 1 or 2 Hours Used: xxxx [H]

The lamp is at the end of its usable life. Please replace the lamp.

Note

If you entered an incorrect address in a test, you may not receive an Alert mail.

Should this happen, check if the Recipient’s Address is correctly set.

Test Mail is not available until either Sender’s Address, SMTP Server’s Name or

Recipient’s Address 1-3 is completed.



•

Operation using an HTTP browser (Continued)

Structure of the HTTP Server

Once the projector is connected to a network and congured correctly, the following screen

is displayed through the web browser. The functions that can be controlled vary depending

on the input signal to the projector.

http:// <the projector’s IP address> /index.html

Function Setting

Description

Power panel On/Off

Controls projector power

Picture panel

BRIGHTNESS

– Increases or decreases the brightness value

CONTRAST

– Increases or decreases the contrast value

COLOR

– Increases or decreases the color value

HUE

– Increases or decreases the hue value

SHARPNESS

– Increases or decreases the sharpness value

Controls the video

adjustments of the

projector

Volume panel

increases the output volume

decreases the output volume

Controls projector volume

Source select

panel

COMPUTER1 – Switches to the COMPUTER 1 IN connector

COMPUTER2 – Switches to the COMPUTER 2 IN connector

COMPUTER3 – Switches to the COMPUTER 3 IN connector

COMPONENT – Switches to the COMPONENT IN connectors

VIDEO – Switches to the VIDEO IN connector

S-VIDEO – Switches to the S-VIDEO IN connector

This switches the input

connector of the projector

Mute panel PICTURE ON – Mutes the video

PICTURE OFF – Cancels the video muting

SOUND ON – Mutes the audio

SOUND OFF – Cancels the audio muting

OSD ON – Mutes the on-screen display

OSD OFF – Cancels the muting of the on-screen display

ALL ON – Mutes all functions

ALL OFF – Cancels the muting of all functions

This controls the mute

functions of the projector

Projector

status panel

Refresh – Updates the panel with the latest information available

Lamp1/2 life remaining – Displays the remaining life of Lamp 1/2

Lamp1/2 time – Displays Lamp 1/2 use in hours

PJ time – Displays the number of hours the project has been used

Error Status – Displays the status of projector errors

This displays the status of

selected projector

functions



Maintenance

CAUTION

The product’s light sources are mercury lamps that light at increased internal pressure. Be

sure to fully understand the following characteristics of the lamps and handle them with

extreme care.

The lamps may burst with a loud noise due to impact or deterioration, or fail to light at

the expiration of its life.

How long it takes before the lamps burst or the life expires may vary greatly by lamp.

Some may burst shortly after rst use.

Burst is likely to happen if the lamps are used after the replacement period has

elapsed.

When a lamp bursts, the broken pieces of glass may get inside the product or be released

outside from the openings for ventilation.

When a lamp bursts, a slight amount of mercury gas enclosed in the lamp along with

glass dust may be released from the openings for ventilation.

Immediately replace the lamp when a sign appears on the screen.

When the replacement time approaches, a message will appear on the screen.

The risk of burst will increase if a lamp is continuously used without being replaced.

Frequently check the used hours and prepare spares when the replacement time

approaches. (Refer to “Usage time” in the “Status display”

p.59

)

When a lamp is broken

If glass components, including a lamp or lens, should break, handle the broken pieces

with care to avoid injury and contact your dealer for repair service.

In the event of lamp burst, unplug the product from the wall outlet, leave and completely

ventilate the room. Then, thoroughly clean the area around the projector and discard

any edible items placed in that area.

When a lamp bursts, consult a doctor if glass dust or mercury gas gets into your eyes

or you breathe it.

•



•



•

About the lamps

Maintenance

When a lamp reaches the end of it’s usable life, the following message is displayed.

Replace the lamp.

The projection lamps should be replaced when they burn out. They should only be replaced

with a specied replacement part, contact your local dealer if unsure.

CAUTION:

The lamp contains a certain amount of mercury and should be disposed of according to

local ordinance regulations.

Avoid touching the glass surface of the new lamp: doing so may shorten its operation

life.

If the lamp’s useful life ends and projector could not turn on over 2100 hours, please

have the projector serviced.

•

Notes

The lamps are positioned differently. Use extra caution not to force the lamps when

replacing.

Installation of both lamp modules (Lamp 1 and Lamp 2) is required to operate the

projector in dual or single lamp mode. If only a single lamp module is installed, the

projector’s lamp will not turn on and will appear as a lamp failure.

WARNING

If the projector is mounted on the ceiling, it is strongly recommended that you

contact a Toshiba dealer when the lamp has to be exchanged. Do not attemp to

replace the lamp by yourself.

If you uncover the lamp while the projector is mounted on a ceiling, there may

be a danger of damage from falling pieces of glass if the lamp is broke, resulting

in possible injury. In addition, viewing at high elevations can also be potentially

hazardous. Do not attemp to replace the lamp by yourself.

Always use lamp "TLPLW25" (sold separately) when replacing the lamp.

Using a lamp other than the one specied may cause a malfunction or damage to the

unit due to the difference in the connector shape or the lamp rate.

•

CAUTION

If you have been using the projector, the lamp will be very hot, and may cause

burn injuries.

Wait 1 hour or longer for the lamp to cool before replacing it.

If the lamp should break, please handle with care to avoid injury due to broken

pieces and contact your dealer for repair service.

•

Replacing the lamps

Maintenance

To replace the lamps, refer to the following instructions.

Unplug power cord.

Wait until lamp is sufciently cooled.

Loosen the captive screw (A) on the lamp cover.

Remove the lamp cover by sliding it in the direction of the arrow (B).

Loosen the two captive screws (A) on the lamp module. Lift the module

handle up (B) in the direction shown.

Pull rmly up the module handle to remove the lamp.

Replace the lamp as shown.

Note

The lamps are positioned differently. Take extra caution not to force the lamps

when replacing.

Reverse steps 3 to 5 to install the new lamp module and replace the lamp cover.

Note

The lters should be replaced when replacing the lamp modules.

•

Replacing the lamps (Continued)

Maintenance

Resetting the lamp hours counter

After replacing the lamp(s), the lamp hour counter(s) should be reset to zero. Refer to

the following guide:

Press the [MENU] button on the control panel or remote to open the Main menu.

Press the

button to move to the [Reset] menu and press Enter.

The Reset menu is displayed.

Select [Clear lamp1 time] or [Clear lamp2 time] using

and press Enter.

A conrmation box is displayed.

Select [OK] using

and press Enter to reset the selected lamp

hours to zero.



Notes and Precautions

The Lamp1/2 time item in the Status display, Usage time screen indicates the time of

lamp use (use it as a rough estimate or guide for lamp life)

p.59

Please replace the lamp after 2000 hours of use with Lamp power set to Standard or

3000 hours of use with Lamp power set to Low

p.58

Attach the lamp cover correctly so that it is secure and not loose. If it is not attached

correctly, the projector may fail to turn on or the lamp may fail to come on.

There may be cases where the lamp stops working before the above mentioned period

expires or before the replacement message is displayed.

Always replace the lamp with a new one.

The lamp is made out of glass. Do not touch the glass surface with your bare hands,

bang it, or scratch it. (since dirt, jolts, scratches and other similar particles may affect

the lamp).

About the lamp replacement message

The projector’s lamp replacement message displays after an appropriate period based on

the use period selected in [Lamp power].

When the replacement time approaches, the message of “The lamp1 and lamp2 has

reached the end of its usable life. Please replace the lamp.” is displayed when power is

turned on and turned off. This display disappears when you press any key.

•

Replacing the lamps (Continued)

Maintenance

Lens and main unit cleaning

WARNING

Request cleaning and maintenance of a ceiling-mounted unit from your

projector dealership. Attempting to clean the unit or replace the lamp in a high

location by yourself may cause you to fall, possibly resulting in injury.

•

Lens cleaning

Clean the lens with a commercially available blower

and/or lens cleaner.

The lens is easily scratched, so do not rub it with hard

objects, or strike it.

Main unit cleaning

Always unplug the power cord before cleaning the main

unit.

Wipe dirt off the main unit gently with a soft cloth.

Do not wipe the main unit with a damp cloth.

Doing so may allow water to get inside, resulting in

possible electric shock or unit failure.

Do not use benzene, thinner or other similar

chemical solutions as they may deform or discolor

the unit or damage the paint surface.

Do not use a chemically saturated cloth.



•



•

Cleaning the lters

The projector uses three lters to keep the fans free of dust and other particles, and should

be cleaned every 500 hours of operation. In dustier environments, it is recommended to

clean the lters more frequently. If the lter is dirty or clogged, your projector may overheat.

When the message below is displayed the lters must be cleaned.

Note

When the Please clean lter message is displayed, please clean or replace all three

lters at the same time to synchronize the hours used display. The Filter Warning item

should be enabled in the Setting 3 menu

p.58

Refer to the following guide to clean the lters.

Lift the projector to clean the lter located at

the bottom.

Note

Only clean the outside of the exhaust vents with a

vacuum cleaner.

The left-hand lter can be cleaned as shown in

the right gure.

The rear lter can be accessed as shown.

Once the lters are cleaned, please reset the

lter time using the Reset menu

p.73

Note

Using the projector without the air lters tted inside allows dirt and dust into the

projector, causing failure.

WARNING

Request cleaning and maintenance of a ceiling-mounted unit from your projector

dealership.

Attempting to clean the unit or replace the lamp in a high location by yourself

may cause you to fall, possibly resulting in injury.

•



•

Bottom

Maintenance

When the lamps are replaced, the lters should also be replaced, not cleaned.

Refer to the following guide to replace the lters.

CAUTION

Do not drop the projector on your hand or ngers while lifting the projector to

replace the lters. Doing so could injure your hand or ngers.

•

Note

The side and the rear lters can be pulled out from

the slots located at the bottom as shown.

Gently slide the lter holders in the direction

shown.

Lift the lter foams from all three lter

holders in the direction shown.

Remove them completely from each lter

holder and discard.

Place a replacement foam and press down

rmly.

Replace the lter holders by pushing gently

in the direction shown.

Note

When dirt and dust build up in the filter, the air circulation inside the projector is

affected and the internal temperature will rise, causing the projector to stop working or

malfunction.

Be sure the lter is inserted all the way into the slot. Leaving gaps will allow dust and

dirt to get inside the projector again.

When you purchase a new lamp, new lters are also provided. If a lter is torn or dirty,

please replace with new one. Continuing to use a ripped lter will allow dust and dirt to

get inside the projector.

Never run the projector with the lters removed. It is recommended that you clean the

•

Replacing the lters

Bottom

Resetting the lter time counter

After replacing the lters, the lter time counter should be reset to zero. Refer to the

following guide:

Press the MENU button on the control panel or remote to open the Main menu.

Press the

button to move to the [Reset] menu and press Enter.

The [Reset] menu is displayed.

Select [Clear lter time] using

and press Enter.

A conrmation box is displayed.

Select OK using

and press Enter to reset the lter time to zero.



Others

Trouble indications

The indicator lights to inform you of internal abnormalities.

ON/STANDY LED

Projector Status LED

Condition

LED Sequence Projector

Condition

AC Off Blank Off

Cooling Orange Blink 0.5 sec On

0.5 sec Off After Power Off

Power Up Sequence Green Blink 0.5 sec On

0.5 sec Off Power Up

Standby / Idle Orange On On

Power On Green On On

Status LED

Projector Status LED Condition LED Sequence Projector

Condition

Normal Condition Off Off Power On

Cover ERROR Blink Red once

(repeat)

0.5 sec On

2.5 sec Off ERROR

Temperature

ERROR

Blink Red twice

(repeat)

0.5 sec On

2.5 sec Off

x 2 times

2.0 sec Off

ERROR

Power ERROR Blink Red 3 times

(repeat)

0.5 sec On

2.5 sec Off

x 3 times

2.0 sec Off

ERROR

Fan ERROR Blink Red 4 times

(repeat)

0.5 sec On

2.5 sec Off

x 4 times

2.0 sec Off

ERROR

Key lock Active

(when key pressed)

Orange On Key lock Active

Idle Green On On

Lamp LEDs

Projector Status LED Condition LED Sequence Projector Condition

Lamp Off Off Off Always

End of Lamp Life Red Blink 0.5 sec On

0.5 sec

Off

Always

No Lamp Blink Red once

(repeat)

0.5 sec On

2.5 sec

Off

ERROR

Lamp ERROR Blink Red 6

times (repeat)

0.5 sec On

2.5 sec

Off x 6 times

2.0 sec

Off

ERROR

Cooling Lamp Orange Blink 0.5 sec On

0.5 sec

Off

Switching lamp 1 and

Re-light Up

Sequence

Green Blink 0.5 sec On

0.5 sec

Off

Power Up

Lamp Life Over

(cannot turn on)

Red On On Always



Others

ON/STANDBY STATUS LAMP1 LAMP2

If you think something is wrong, check the followings before contacting customer service.

Please see “Trouble indications”

p.74

as well.

If This Happens Check

No power Is the power cord plugged in? Is it connected to the projector?

Is the main power switch turned on?

p.36

Is the lamp cover attached properly?

p.67

•

Power goes out

during use

Is the ambient temperature high?

p.74

Is the air intake or air exhaust blocked?

p.74

•

No picture

Is the correct source selected?

p.38

Is the mute function on?

p.43

Is the brightness setting minimized?

p.50

Are the connections set up correctly?

p.28

Are all the connected devices functioning properly?

•

No audio

Is the mute function on?

p.43

Is the volume setting minimized?

p.40

Are the connections set up correctly?

p.28

Are all the connected devices functioning properly?

•

Picture not

displayed

correctly

Is the input signal supported by the projector?

p.78

Is there something generating an abnormal video signal, for

instance the video tape?

•

Picture blurred

Part of picture

out of focus

Is the lens dirty?

p.70

Is the lens focus adjusted optimally?

p.39

Is the projection distance within the supported range?

p.26

Is the projector’s screen placement angle tilted too far?

p.26

Are the sharpness or phase adjustments off?

p.50

p.53

•

Image is dark

Are the brightness or contrast adjustments off?

p.50

Is the lamp nearing the end of its service life?

p.59

•

Colors too light

Bad shading

Are the color, tint, R-level, G-level, or B-level adjustments off?

p.50

p.51

Is the screen dirty?

Is the lamp nearing the end of its service life?

p.59

•

Control panel key

doesn’t work

Is the key lock function on?

p.56

•

Remote control

doesn’t work

Are the remote control’s batteries drained?

Are the batteries inserted into the remote control correctly?

p.23

Is the remote control being used within the effective range?

p.23

Are there any obstructions between the remote control and

projector?

Are there any uorescent or other bright lights shining at the

projector infrared remote sensors?

•

Before calling service personnel

Others

Specications

List of general specications

Item Specication

Display type

TI DMD 0.65-inch x 1, 12 degrees, Type A, LVDS DLP

w/DDP3020

Resolution WXGA 1280 x 800

Bandwidth Up to UXGA 1600 x 1200 @ 60 Hz <170 MHz>

Color 16.7 Million (24-bits/Pixel)

Aspect Ratio 4:3, 16:9, 16:10, Letterbox, True, Standard

Lens Shift Powered, V (0-100%) & H (+/-20%)*

Keystone Correction

Horizontal keystone: V (+/-40°), H (+/-35°) @ (TR 1.78),

optical offset 50% under single direction

Projection Methods Desktop front/rear,

Ceiling front/rear

Color Wheel 4-segment (W95°) ; 6-segments

Throw Ratio (STD Lens) 1.80 (Wide) - 2.38 (Tele)

Power Consumption

Max dual lamp

730 Watts @100V/7.4A

690 Watts @240V/3.0A

Max single lamp

380 Watts @100V/3.8A

370 Watts @240V/1.6A

Standard Mode dual lamp

Typical 710 watts @100V/7.2A

Typical 670 watts @240V/2.9A

Standard Mode single

lamp

Typical 370 watts @100V/3.7A

Typical 360 watts @240V/1.6A

Low Mode dual lamp

Typical 570 watts @100V/5.7A

Typical 550 watts @240V/2.4A

Low Mode single lamp

Typical 310 watts @100V/3.1A

Typical 300 watts @240V/1.3A

Standby Power < 5 watts (for Power saving); <30 watts (for Normal)

Weight (without lens) 17 ± 1 kg

External Dimensions

(not including protrusions)

505 mm x 385 mm x 194 mm (W x D x H)

Cabinet material

Top case: Sabic (GE) PC 945)

Lamp Door: Sabic (GE) PC 945

Bottom case: TEIJIN PC MN-3600HC

Operation environmental

condition

Temperature:

5°C to 35°C.

High altitude: 5°C to 23°C (4000-10000 feet)

Relative Humidity:

10% to 85%, relative, non-condensing

Storage environmental

condition

Temperature: -10°C to 60°C (sea level to 30000 ft)

Relative Humidity: 5% to 95%, relative, non-condensing

* The values may vary depending on the lens.



Item Specication

Safety Certications

UL (le no.: E134786) (UL60950-1/CSA60950-1)

CB (IEC60950-1) edition.1

S-UL (J60950), PSB

FCC part15 subpart B class B, IECS-003 class B

CE (EN55022 Class B, EN55024, EN61000-3-2,

EN61000-3-3)

C-TICK (AS/NZS CISPR.22 Class B)

CCC / Korea EK

Security

Kensington slot

Slot for prevention of theft chain

Projection lens lock (screw at bottom)

Connection terminal

RGB (Analog) D-SUB x 1 (pin 6, 7, 8, 10, 11 GND short), 5 BNC x 1

DVI-D With HDCP Yes

Video (CVBS) Composite video (RCA x 1)

S-Video (Y/C) Mini-DIN

Component Video YPbPr (YCbCr), RCA x 3

Audio in (Video)

Video, S-Video share Left (mono)/Right (RCA x 2); YPbPr

Left (mono)/Right (RCA x 2)

Audio in (PC)

DVI-D x 1, D-SUB x 1 5BNC x 1; type: Mini-phone jack (3.5

mm) Maximum input level : 2.0 Vrms

Audio out (PC)

Mini-phone jack (3.5 mm) x 1 (when plug in audio out cable

projector speakers disable) Audio output level = Audio input

level X 4.5 db

Screen Control Mini-phone jack (3.5 mm) x 1

USB 1.1

Serial Port (RS-232) RS-232 9 pin (Cross)

Monitor Out D-SUB x 1 (pin 6, 7, 8, 10 GND short)

LAN Control RJ-45 10/100 Mbps

Notes

This model complies with the above specications.

Designs and specications are subject to change without notice.

This model may not be compatible with features and/or specications that may be

added in the future.

Separately sold product

Replacement Lamp Model: TLPLW25

•



Others

Compatible input signal list

The following table shows compatible signal types, their resolution and frequency refresh rates.

Horizontal: 15 kHz, 31 kHz to 90 kHz, Vertical: 50 Hz to 85 Hz

Signal Resolution (DPI)

Frequency Refresh

Rate (KHz)

Frequency Refresh

Rate (Hz)

NTSC - 15.73 60.00

PAL - 15.63 50.00

PAL60 - 15.73 60.00

SECAM - 15.63 50.00

VESA D 640 x 480 31.47 59.94

MAC D 640 x 480 35.00 66.67

VESA D 640 x 480 37.86 72.81

VESA D 640 x 480 37.50 75.00

VESA D 640 x 480 43.27 85.01

VESA D 800 x 600 35.16 56.25

VESA D 800 x 600 37.88 60.32

VESA D 800 x 600 48.08 72.19

VESA D 800 x 600 46.88 75.00

VESA D 800 x 600 53.67 85.06

MAC D 832 x 624 49.72 74.55

VESA D 1024 x 768 48.36 60.00

VESA D 1024 x 768 56.48 70.07

MAC D 1024 x 768 60.24 74.93

VESA D 1024 x 768 60.02 75.03

VESA D 1024 x 768 68.68 85.00

VESA D 1152 x 864 67.50 75.00

VESA D 1280 x 768 47.80 60.00

VESA D 1280 x 768 60.30 75.00

VESA D 1280 x 768 68.60 85.00

VESA D 1280 x 800 49.70 60.00

VESA D 1280 x 800 62.80 75.00

VESA D 1280 x 800 71.60 85.00

VESA D 1280 x 960 60.00 60.00

VESA D 1280 x 1024 63.98 60.02

VESA D 1400 x 1050 65.30 60.00

VESA D 1440 x 900 55.90 60.00

VESA D 1440 x 900 70.60 75.00

HDTV (1080i)(1125i) - 1920 x 1080 33.75 60.00 Interlace

HDTV (1080i)(1125i) - 1920 x 1080 28.13 50.00 Interlace

HDTV (720p)(750p) - 1280 x 720 45.00 60.00 Progressive

HDTV (720p) - 1280 x 720 37.50 50.00 Progressive

SDTV (576p)(625p) - - 31.25 50.00 Progressive

SDTV (480p)(525p) - - 31.47 59.94 Progressive

DVD YCbCr - - 15.73 59.94 Interlace

DVD YCbCr - - 15.63 50.00 Interlace

Note

Images above agged with “D” are supported by digital signal.

An image with higher or lower resolution than the projector’s native resolution

(1280 x 800) will be compressed.

Some Composite and Sync on Green signals may not be displayed correctly.

Signals other than those specied in the table above may not be displayed correctly. If

this should happen, change the refresh rate or resolution on your PC. Refer to Display

Properties help section of your PC for procedures.



•

Specications (Continued)

CONTROL terminal

Pin assignment

No.

Signal Name Description

D sub 9 pin connector

1 DCD Data carrier detect

2 RXD Receiving data

3 TXD Sending data

4 DTR Data terminal ready

5 GND Signal ground

6 DSR Data set ready

7 RTS Request to send

8 CTS Consent to send

9 RI Ring indicator

Note

Use a cross cable (not supplied) for RS232C control.

Interface format

Header: ‘#’

Delimiter: CR (0x0Dh)

Command: 3 Byte (ASCII Character)

Parameter: Variable length

(If the command has a parameter, place a colon before the parameter.)

Header:

‘=’

Delimiter CR (0x0Dh)

Command 3 Byte (ASCII Character, command echo)

Parameter Variable length

(If the command has a parameter, place a colon before the parameter.)

Main Commands

Item Command

Power off PON

Shutdown PSD

Status display on DON

Status display off DOF

Note

Contact your dealer for control cable and other commands.



•



•

Specications (Continued)

Pin assignment of COMPUTER 1 IN

Pin No.

Pin description

RGB Signal (analog) Y/Cb/Cr Signal

1 Red Cr

2 Green or Sync on Green Y

3 Blue Cb

4 Ground

5 Ground

6 Red Ground Cr Ground

7 Green Ground Y Ground

8 Blue Ground Cb Ground

9 No Connection

10 Sync Signal Ground

11 No Connection

12 Bi-directional Data (SDA)

Horizontal Sync or Composite

Sync

Vertical Sync

15 Data Clock

Screen Trigger

When the projector is powered ON, the screen trigger output sends a low voltage trigger to

the screen controller and the screen will go down. When the projector is powered OFF, the

screen trigger stops sending a low voltage trigger to the screen controller and the screen

will go up.

Note

To use this feature, you must turn on the Screen Trigger function

p.58

Note

Screen controllers are supplied and supported by screen manufacturers.

Do not use this jack for anything other than intended use. Connecting the wired remote

control to the SC. TRIGGER Mini Jack causes damage to the remote control.



•

Mini D sub 15 Pin connector

1511

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba TDP-WX5400 in the language / languages: English as an attachment in your email.

The manual is 7,6 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Toshiba TDP-WX5400 Manual

Product: