497499
26
Zoom out
Zoom in
Previous page
1/59
Next page
26
8-4-3. Wiring Connection
WARNING
To plug the cable in the plug receptacle, take the
following precaution.
THIS APPLIANCE MUST BE EARTHED.
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLORED
IN ACCORDANCE WITH THE FOLLOWING CODE:
Place your finger on the lower part and push up
to open the screw cap.
(1) Open the screw caps and remove the two screws
securing the front cabinet.
(2) Close the screw caps as behind.
(3) Open the vertical airflow louver horizontally by
hand.
(4) Slightly open the lower part of the front cabinet
then pull the upper part of the front cabinet
toward you to remove it from the rear plate.
Fig. 8-4-6
How to open the screw cap
3
2
2
1
1
4
4
Vertical air flow louver.
Fig. 8-4-5
As the colors of the flexible cord of this appliance
may not correspond with the colored markings, to
identify terminals in your plug, as follows:
Connect BROWN colored core to plug terminal
marked letter L.
Connect BLUE colored core to plug terminal marked
letter N.
Connect GREEN AND YELLOW colored core to plug
terminal marked Earth Symbol
.
The installation of the cables has to be done in such
a way that the basic insulated wires for the infrared
sensor can not be touched.
<How to remove the front cabinet>
L
N
L
N
-LIVE
-NEUTRAL
-EARTH
: Brown
: Blue
: Green and Yow
Taking out the power cord
Cut off the slitted portion in the side face of the
rear panel to take out the power cord. After
this, remove burrs, sharp edges, etc., to
smooth the cut face..
<How to connect the power cord>
(For RAS-07YK-E, RAS-07YK-ES, RAS-10YK-E,
RAS-10YK-ES
only)
For the air conditioner that has no power cord,
connect a power cord to it as mentioned below.
After removing the front cabinet, remove the
terminal cover and the cord clamp.
Connect and secure the power supply cord and
secure the cord clamp and the terminal cover.
Cut the rear panel following the cutting mark and
put the power supply cord through the notch.
Be sure to smooth out the notch with a file, etc.
Slitted portion
Cord clamp
Terminal cover
Screw
Power supply
cord
Terminal block
Earth line
Screw
Screw
L
N
Fig. 8-4-7
<Stripping length of power cord>
NOTE :
Use standard wire only.
Wire type: More than H05-RN-F
Fig. 8-4-8
Earth line
40mm
10mm
10mm
30mm
L
N
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba RAS-10YAX-T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba RAS-10YAX-T in the language / languages: English as an attachment in your email.

The manual is 10,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info