497499
24
Zoom out
Zoom in
Previous page
1/59
Next page
24
8-4. Indoor Unit
K Installation place
A place which provides the spaces around the
indoor unit as shown in the diagram in section 8-2.
A place where there is no obstacle near the air inlet
and outlet.
A place which allows an easy installation of the
piping to the outdoor unit.
A place which allows the front panel to be opened.
CAUTION
Direct sunlight to the indoor unit wireless
receiver should be avoided.
The microprocessor in the indoor unit should
not be too close to r-f noise sources.
(For details, see the owners manual.)
<Remote control>
A place where there are no obstacles such as a
curtain that may block the signal from the remote
control.
Do not install the remote control in a place exposed
to direct sunlight or close to a heating source, such
as a stove.
Keep the remote control at least 1 m apart from the
nearest TV set or stereo equipment.
(This is necessary to prevent image disturbances
or noise interference.)
The location of the remote control should be
determined as shown below.
Fig. 8-4-1
(Top view)
Indoor unit
5m
5m
45˚
45˚
Remote
control
Reception
range
*:Axial distance
Remote
control
Reception
range
7m
(Side view) Indoor unit
*7m
75˚
8-4-1. Cutting a Hole and Mounting
Installation Plate
<Cutting a hole>
When installing the refrigerant pipes from the rear.
Fig. 8-4-2
(1) After determining the pipe hole position with the
mounting plate (80 mm ), drill the pipe hole
(ø65 mm) at a slight downward slant to the
outdoor side.
NOTE :
When drilling the wall that contains a metal lath,
wire lath or metal plate, be sure to use a pipe hole
brim ring sold separately.
<Mounting the installation plate>
For installation of the indoor unit, use the paper
pattern on the back.
The center of the piping slot
is above the arrow.
The center of the pipe
hole is above the arrow.
80mm
Pipe hole
65mm
40,5
mm
Fig. 8-4-3
Indoor unit
Pipe
hole
65,5mm
Thread
Weight
1
Installation
plate
5
Mounting
screw
Pipe hole
65,5mm
Anchor bolt hole
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba RAS-10YAX-T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba RAS-10YAX-T in the language / languages: English as an attachment in your email.

The manual is 10,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info