807536

Torqeedo Cruise 6.0 FP TorqLink Manual

82
Zoom out
Zoom in
Previous page
1/92
Next page
82
DE EN
10.4.4 Propeller
NOTE! If the maximum speed of the boat exceeds 14 knots through the water
(STW), the optional folding propeller must be used to avoid damage to the motor
caused by excessive propeller rotational speeds
DANGER
Danger of injury or death from rotating propeller. This can result in sever
injuries or death.
• Switch off the system at the battery main switch and secure it against
being switched on again by pulling off the switch handle to prevent the
propeller from starting.
Checking
1. Switch off the system at the battery main switch and secure it against being
switched on again by pulling off the switch handle.
2. Check the propeller for damage such as cracks, chipping and deformation.
3. Check the gap between the pylon and the propeller for foreign objects, e.g.
shing lines, seaweed, etc. Wear gloves when doing this to avoid injury.
4. Dismantle the propeller to remove any contamination.
Disassembly
1
2
4
3
5
TIP! Remove the propeller when the motor is attached to the boat and the boat is
safely on land.
1. Ensure that the motor is securely fastened and secured against falling
(e.g.e.g. on the boat or on a workbench).
2. Remove the galvanic anode (1).
3. Loosen the lock nut (2) with a socket wrench SW17 and unscrew it from the
motor shaft (3).
4. Remove the washer (4).
NOTE! Component damage due to incorrect tool. Do not use force or tools such
as hammers to remove the propeller.
5. Pull the propeller off the motor shaft, move the propeller in different
directions to make it easier to pull off.
6. Remove the thrust washer (5).
7. Clean the motor shaft.
8. Clean the thread of the motor shaft.
Installation
5
4
3
2
1
1. Position the thrust washer (1) on the motor shaft (2).
2. Position the propeller on the motor shaft, noting the installation direction.
3. Position the washer (3) on the motor shaft.
NOTE! Component damage due to thread locking varnish. Do not use locking
varnishes or additives.
4. Screw the lock nut SW17 (4) onto the motor shaft and tighten it.
• Lock nut: 11+/- 1 Nm, 97+/-1 in-lbs
5. Install the galvanic anode (5).
… 82 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Torqeedo Cruise 6.0 FP TorqLink at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Torqeedo Cruise 6.0 FP TorqLink in the language / languages: English, German as an attachment in your email.

The manual is 2.97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Torqeedo Cruise 6.0 FP TorqLink

Torqeedo Cruise 6.0 FP TorqLink User Manual - Dutch, Danish - 92 pages

Torqeedo Cruise 6.0 FP TorqLink User Manual - French, Italian - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info