807535
83
Zoom out
Zoom in
Previous page
1/92
Next page
83
DE EN
10.4.5 Anti-fouling coating
NOTE! Observe national regulations on the processing, application, use and
disposal of anti-fouling coatings. Follow the manufacturer's instructions and
processing instructions.
General instructions
To keep your Cruise system free of fouling, you can do the following:
Remove the Cruise system from the water after each use and clean it.
Regularly clean all components of the Cruise system that are permanently
below the water surface.
Use an anti-fouling coating.
Cleaning the components under the water surface
Before cleaning work, switch off the Cruise system at the main switch and
secure it against being switched on again by pulling off the switch handle.
Do not use tools with sharp edges or abrasive surfaces that may damage
the Cruise system's paintwork.
Using anti-fouling coatings
When using anti-fouling paints, we recommend that all parts of the
Cruise Systems that are permanently below the water surface are coated.
1. Clean the surfaces of the Cruise system that you want to treat.
NOTE! Do not use abrasives to roughen the surface, otherwise the protective
coating will be damaged.
2. Thoroughly mask the anodes and, if necessary, the motor shaft.
3. Observe the processing instructions and the manufacturer's instructions on
personal protective equipment for the respective anti-fouling coating.
Permitted anti-fouling coatings
International Trilux 33 in combination with primer Primocon Sperrgrund
Hempel Silic One in combination with Hempel Light Primer and Hempel
Silic One Tiecoat
NOTE! Do not use metal-containing anti-fouling coatings e.g.products
containing copper.
11 Errors and troubleshooting
11.1 Error messages and errors
Display Cause Troubleshooting
E02 Stator overtemperature
(motor overheated)
After a short waiting time (approx. 10
minutes), the motor can be operated
slowly. Contact Torqeedo Service.
E05 Motor/propeller blocked Set the main switch to the “OFF”
position. Release the blockage and turn
the propeller one turn further by hand.
Reconnect the motor cable.
E06 Voltage at motor too low Low battery state of charge. If necessary,
the motor can be driven slowly from the
stop position.
E07 Overcurrent at the motor Continue driving with low power. Contact
Torqeedo Service.
E08 Circuit board
overtemperature
After a short waiting time (approx. 10
minutes), the motor can be operated
slowly. Contact Torqeedo Service.
E21 Faulty calibration of
tiller / remote throttle
Set forwards/reverse motion
E22 Magnetic sensor
defective
Set forwards/reverse motion
E23 Value range wrong Set forwards/reverse motion
E30 Motor communication
error; error in the power
supply to the motor
Contact Torqeedo Service;
Check that the main switch is in the “ON”
position.
E32 Tiller communication
error / remote throttle
Check the plug connections of the data
cables and cables.
E33 General communication
error
Check the plug connections and the
cables. Switch the motor off and on again.
E34 Emergency kill switch or
kill switch actuated
Make sure that the cause of the error has
been eliminated, set the emergency kill
switch or the kill switch to the position for
normal operation and restart the system.
83


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Torqeedo Cruise 3.0 FP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Torqeedo Cruise 3.0 FP in the language / languages: English, German as an attachment in your email.

The manual is 2.97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Torqeedo Cruise 3.0 FP

Torqeedo Cruise 3.0 FP User Manual - Dutch, Danish - 92 pages

Torqeedo Cruise 3.0 FP User Manual - French, Italian - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info