484003
8
Zoom out
Zoom in
Previous page
1/72
Next page
Babytalker 3500 SEDS
6
8.3 Connecting the Baby Unit to the AC Mains
Insert the small plug of the AC mains adapter in the mains power
connector of the baby unit and plug the AC mains adapter into a mains
connector (230 V / 50 Hz).
8.4 Installing Rechargeable Batteries in the Parent Unit
See Figure on the fold-out page.
Rotate the belt clip upward.
Turn the screw on the cover of the battery compartment at the back of
the parent unit 90° counterclockwise and remove the battery
compartment cover.
Place the NiMH battery pack in the battery compartment.
Ensure that the tab of the battery pack fits in the corresponding recess
and that the polarity matches the figure (B).
Carefully close the battery compartment and rotate the belt clip back
downward.
8.5 Installing the Parent Unit charging cradle
Insert the small plug of the AC mains adapter in the mains power connector of the charging station and
plug the AC mains adapter into a mains connector (230 V / 50 Hz).
Place the parent unit in the charging station. The red Charging LED will go on.
9 Operation and Use
9.1 Switching the Baby Unit and Parent Unit On and Off
Press the On/Off switch to switch on the parent unit. The power LED will lit.
Press the On/Off switch to switch on the baby unit. The power LED will lit.
Press the On/Off switch to switch on the parent unit. The power LED will go out.
Press the On/Off switch to switch off the baby unit. The power LED will go out.
9.2 Checking the Link Between the Parent Unit and the Baby Unit
You should always check the wireless link when you use the babyphone for the first time.
Put the parent unit in the same room as the baby unit, separated by at least two metres.
Switch on both devices. The parent unit will try to establish a connection with the baby unit.
The green Link LED on the parent unit blinks while it is trying to establish a connection.
If NEMo mode is turned OFF (see “9.4 NEMo Switch Setting”): The LED stays on continuously
after a connection has been established.
If NEMo mode is turned ON: The green link LED on Parent Units will flash until they communicate.
Once the link is established, the LED will light continuously. After a while, when the baby unit doesn’t
capture any sound, the LED will flash every 5 seconds because the baby unit stops the transmission.
CAUTION
The mains connector must be within easy reach so you can
quickly unplug the power cable in an emergency.
Use only the supplied AC mains adapter (6 V DC / 300 mA).
CAUTION
Use only the supplied NiMH battery pack in the parent unit.
Do not turn the screw past the ‘Open’ point.
It takes around 10 hours to fully charge the batteries.
The parent unit will try to establish a connection with the baby unit. If the Link LED goes
on, a connection has been established. If it does not, see below.
SEDS
LONG
ECO
6V/300mA
8
B
+
AB
18
21
20
15
17
4
2
13
15
17
4
2
13
13
13
13
13
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Topcom Babytalker 3100 - KS 4231 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Topcom Babytalker 3100 - KS 4231 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info