782195
19
Zoom out
Zoom in
Previous page
1/240
Next page
19GB
12 Do not overstretch
-Avoid abnormal working postures. Make sure
you stand squarely and keep your balance at all
times.
13 Take care of your tools
-Keep your tools sharp and clean in order to work
well and safely. Follow the maintenance infor-
mation and the instructions for changing tools.
Check the power plug and cable on a regular
basis and have them replaced by an authorized
specialist if they are damaged. Check theexten-
sion cable regularly and replace it if damaged.
Keep handles dry and free from oil and grease.
14 Pull out the power plug
-When tools are not in use, before starting any
maintenance work or when changing attach-
ments such as saw blades, drill bits and all kinds
of mounted tools.
15 Always remove keys and wrenches after use
-Always check that keys, wrenches and other
adjusting tools have been removed before you
switch on the equipment.
16 Avoid unintentional starting
-Never carry a tool with your nger on the switch
button while the tool is connected to the power
supply. Make sure that the switch is turned off
when connecting the tool to the power supply.
17 When using an extension cable outdoors
-Check that it is approved for outdoor duty and is
marked accordingly.
18 Be alert at all times
-Watch what you are doing. Use common sense
when working. Never use the tool when you are
distracted.
19 Check your tool for damage
-Before using the tool again, check the safety
devices or any slightly damaged parts to en-
sure that they are in good working order. Check
that the moving parts are working correctly, that
they do not jam, and that no parts are damaged.
Make sure that all parts are tted correctly to
ensure that the equipment remains safe to use.
Unless otherwise stated in the operating instruc-
tions, damaged guards and parts have to be re-
paired or replaced by a customer service work-
shop. Damaged switches have to be replaced
by a customer service workshop. Never use an
electric power tool with a switch that cannot be
turned on and off.
20 Important.
-For your own safety you must only use the ac-
cessories and additional units listed in the oper-
ating instructions or recommended or specied
by the manufacturer. The use of mounted tools
or accessories other than those recommended
in the operating instructions or catalog may
place your personal safety at risk.
21 Repairs may only be carried out by a qualied
electrician
-This electric power tool complies with the perti-
nent safety information. Repair work must only
be carried out by a trained electrician, otherwise
the equipment may cause accidents.
22 Connect up the dust extraction system
-If there are provisions for connecting up a dust
extraction system, make sure that such a system
is tted and in use.
Additional safety instructions
Switch the machine off immediately and pull the
power plug in an emergency.
Follow all these safety instructions before and while
working with the saw.
Do not use this saw to cut re wood.
Do not use this saw to cross-cut roundwood with-
out a suitable holding device.
The machine is equipped with a safety switch to
prevent it from being switched on again acciden-
tally after a power failure.
If you need to use an extension cable, make sure
its conductor cross-section is big enough for the
saw’s power consumption. Minimum cross-section
1 mm2.
If you use a cable reel, the complete cable must be
pulled off the reel.
Persons working on the machine should not be dis-
tracted.
After you have switched off the motor, never slow
down the saw blade by applying pressure to its
side.
Only t blades which are well sharpened and have
no cracks or deformations.
Faulty saw blades must be replaced immediately.
Never use saw blades which do not comply with the
data specied in this manual.
It is imperative to make sure that all devices which
cover the saw blade are in good working order.
Never dismantle the machine’s safety devices or
render them inoperative.
Damaged or faulty safety devices have to be re-
placed immediately. Never cut workpieces which
are too small to hold securely in your hand.
Never load the machine so much that it cuts out.
Always press the workpiece rmly against the saw
table.
Never remove loose splinters, chips or jammed
pieces of wood when the saw blade is running.
Switch the machine off to rectify faults at the
blocked plug-in tool. - Pull the power plug- Remove
the blockage. Important! Risk of injury from saw
blade! Wear gloves. Carry out a trial run without a
workpiece. Ensure that no unusual noise or vibra-
tion occurs. Should this be the case, switch the unit
off and contact the manufacturer.
Carry out retooling work, adjustments, measure-
ments and cleaning jobs only when the motor is
switched off. - Pull the power plug. -
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toolson DKS1600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toolson DKS1600 in the language / languages: All languages as an attachment in your email.

The manual is 8.64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info