Manual Toolland FT 92 (page 19 of 22) (English, German, Dutch, French, Portuguese, Spanish)

622632

Zoom out

Zoom in

1/22

FT 92 English

www.toolland.eu 19

4. DETECT GAS LEAKS

 To find the gas leak you must brush

soapy water on all the fittings and

connections of the gas circuit. If there is

a leak you will notice bubbles.

 If you notice bubbles you must close the

leak.

 If there is still a leak after you closed the

leak you must close the gas cylinder

valve and request professional

assistance.

 Only check for leaks when the appliance

has cooled down completely.

 WARNING! Never use a flame to detect a

gas leak!

5. USE

5.1 PREPARATIONS

 Check the appliance for possible transport

damage. Never use a damaged appliance.

 Follow all the instructions carefully.

 Never place the gas cylinder in front of

the heater. Place the gas cylinder and the

appliance on a stable and level surface.

 Always check if the specifications of the

regulator and the hose are the same as

the specifications mentioned on the rating

label.

 Take the cabinet on the rear cylinder

cover unscrew of the two fixing screw.

 The heater must be used with a regulator

and hose. The flexible hose must be

checked regularly whenever the cylinder

is replaced to be sure it has no scratches

or cuts and that it is in a perfect state. It

must be replaced in any case before the

expiry date stamped on the hose itself.

 Connect the flexible tube to the hose

union of the pressure regulator and to

that of the tap, making sure that the

metal bands are tight and paying

particular attention not to tamper with or

damage any component or fitting.

 Before connecting the cylinder, make sure

that its tap is closed and that there are

no open flames (lit oven, etc.) in the

place where you are working. Screw the

pressure regulator onto the cylinder,

keeping these warnings in mind:

 Check that the gasket seal is in

good condition.

 Attach the regulator to the tap,

screwing the nut tightly

counterclockwise.

 Carefully check that there is no

gas leaking from the connection

using soapy water: if there is a

leak, bubbles will form; tighten

the connection more or seek

professionally qualified service.

 Place the cylinder in its compartment,

taking care that the tube is not twisted or

choked and isn't touching hot parts.

 Hook the rear cylinder cover on the

cabinet, insert the two hooks in the

respective holes of the cabinet and put

the wing screws.

 To replace the cylinder, make sure that its

tap is closed and that there are no open

flames (lit oven, etc.) or sources of heat

in the place where you are working; we

recommend that you check that the

gasket seals of the regulator and flexible

rubber tube are in good condition and

replace them, if necessary.

 To not mishandle the connections or

other components.

 Do not turn the cylinder upside down to

completely use its contents: this releases

liquid residues left in the tank that will

irreparably damage the heater.

 Do not disconnect the pressure regulator

from the cylinder when the cylinder tap is

open.

 The manufacturer will not be responsible

if one of the above points is disregarded.

5.2 START AND STOP

Pos. 1 (Start and Maximum Heating)

Pos. 2 (Medium)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Toolland FT 92 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Toolland FT 92 Manual

Product: