Manual Toolland DT 20005 (page 13 of 16) (English, German, Dutch, French)

771265

Zoom out

Zoom in

1/16

DT 20005 English

www.toolland.eu 13

SPRAYING CHEMICALS

This sprayer is intended for use with water

based solutions of proprietary insecticides,

fungicides, weed killers and follar feeds.

Always follow the chemical suppliers on-pack

instructions as well as the instructions listed

below.

 Wear protective clothing, goggles, face

mask and gloves.

 Avoid inhaling spray mist.

 Avoid skin contact with chemicals.

 Work in a well ventilated area.

 Take care to protect children, pets and

fish from exposure to chemicals.

 Wash hands thoroughly after use and

especially before eating.

 Wash any contamined clothing.

 Seek medical attention if spray gets in

your eyes or if you develop any

symptoms after spraying.

 Do not spray near food or food

preparation areas. When spraying crops,

pay particular attention to the chemical

manufacturer’s advice on time before

crops can be eaten, etc.

 Do not spray any solvent based material

e.g. white spirit.

 Spray only thin watery solutions, thicker

mixtures will clog the nozzle.

 Powdered chemicals can be sprayed

successfully if they are not completely

soluble and the solution tends to settle,

spraying can still be successful so long as

the mixture continually agitated.

 If the material to be sprayed contains

sediment, strain the liquid into the

sprayer bottle.

 Do not over-pressurize the bottle, or

tamper with the pressure release valve.

 After use pay particular attention to the

paragraph on cleaning.

 Your sprayer is manufactured from many

different types of plastic material, and

although the liquid you wish to use may

be packed in a plastic container, this is no

guarantee that it will not damage the

sprayer. If you are in any doubt about

any chemical you intend to spray we

recommend that you contact the

consumer service department at the

address given the check its suitability.

MAINTENANCE

Pressure release valve

 The safety valve is designed to release

any excess pressure and to let you

release the pressure after spraying.

 Do not interfere with the setting of the air

pressure safety valve.

Plunger head

 The O-Ring should be kept lubricated to

slide freely in the barrel and so pump air

efficiently.

 To apply grease proceeds as follows.

 Remove the pumps assembly by

unscrewing in an anti-clockwise direction.

 Locate the pump handle into the carrying

position and grip the barrel.

 Unscrew the plunger retaining cap from

the pump barrel by rotating the handle.

 Withdraw the plunger and apply silicone

grease to the O-Ring.

 When re-assembling ensure the O-Ring is

not trapped between the outer edge of

the plunger moulding and the inside of

the pump barrel.

Pump non-return valve:

(Situated at the bottom of the pump barrel)

 This stops the compressed air in the

container from escaping back into the

pump.

 If it is faulty, the unlocked pump handle

will rise when the container is

pressurized.

 To remove the valve, lift the edge of the

valve and pull. (take care not to damage

the sealing face of the barrel).

 To replace place the valve over the centre

hole and push down firmly.

Pump barrel sealing rings

 These make an air tight seal between

both the pump barrel and adapter.

 Also between the adapter and container

when both are screwed down tight.

 To check this, turn the pressurized

sprayer upside down and if there is a

leak, liquid will be forced from the joints.

Nozzle cap

 Keep this clean and free from obstruction.

 Also, the two swirl grooves at the end of

the lance must be kept clean and free

from sediment to ensure a good spray

pattern.

 The nozzle O-Ring should be kept

lubricated with silicone grease.

Lance

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Toolland DT 20005 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0.22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Toolland DT 20005 Manual

Product: