Manual Toolland DT 20005 (page 12 of 16) (English, German, Dutch, French)

771265

Zoom out

Zoom in

1/16

DT 20005 English

www.toolland.eu 12

PRESSURE SPRAYER

DT 20005

WARNING

For your own safety, read this manual

carefully before using this sprayer.

SAFETY INSTRUCTIONS

When using the appliance always observe the

safety instructions.

ASSEMBLY

 Fit the lance assembly to the sprayer by

means of the flexible hose.

 Remove the nut fitted to the lance.

 Insert hose through nut.

 Push the hose fitting fully onto the lance

connector.

 Screw nut tightly onto lance.

 Attach the other end of the hose to the

container using the above method.

 Ensure that the hose is fully pushed on

and that the nut is screwed down tight.

 Fit the carrying strap by threading the

expandable ring through the hole in the

lug moulded into the container base.

 Fit the other end of the strap through the

slot in the top lug and thread through the

metal buckle and adjust length to suit.

OPERATING INSTRUCTIONS

 Ensure that the hose is securely attached

to the sprayer and the lance and the

locking nut are tight.

 Check that the liquid which you intend to

use is suitable (see the spraying chemical

section).

 Fill the container to the desired level

taking care not to exceed the maximum

fill mark.

 Screw the pump firmly home to ensure

an airtight seal.

 Operate the pressure release valve

manually by pulling the blue knob

upwards to ensure it is functioning

correctly.

 Release the pump handle by pressing

down and turning anti-clockwise.

 Pump to pressurize the container.

 When the correct operating pressure has

been reached, the pressure release valve

will vent to discharge excess air.

 The container is adequately pressurized

and does not require further pumping.

Trigger Operation

 The trigger mechanism has been

designed to allow for two modes of

operation, either intermittent or

continuous.

Intermittent

 Depress trigger to operate and release it

to stop spraying.

Continuous

 While depressing trigger push forward

with the thumb to hold in the lock on

position.

 The sprayer will now continue to operate

without any further finger pressure, so

preventing fatigue.

 To turn off the sprayer pull back the level

and release.

 Aim the spray nozzle towards a test area,

squeeze the trigger on the lance and

adjust the nozzle to the desired degree of

fineness by twisting the nozzle from mist

through coarse spray to jet.

 Do not undo the nozzle too far or leakage

will occur from the back of the nozzle.

 If the nozzle continues to spray or drip

after the trigger has been released, it is

because there is air in the discharge

system (lance, handle trigger or hose).

 Purge the system by turning the nozzle to

jet and operating the trigger on the lance

on and off in short bursts until the liquid

shuts off cleanly.

 Collect any chemicals in a separate

container and use later.

 To keep spraying a few pumps at

infrequent interval are all that is required.

 After use and before storage release the

pressure from the container by pulling

the blue knob of the pressure release

valve upwards.

 If the sprayer has been used with

chemicals, discard safely any unused

solution after use.

 Add a little detergent and some warm

water (not hot) to the sprayer.

 Re-assemble the sprayer and spray some

of the contents through.

 Repeat with the clean, cold water.

 Check that the nozzle assembly is free

from sediment.

 If necessary repeat the process until the

sprayer is clean.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Toolland DT 20005 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0.22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Toolland DT 20005 Manual

Product: