485762
11
Zoom out
Zoom in
Previous page
1/30
Next page
50 Toledo
7) Use of extension cables
Use a suitable extension cable only, which is suitable for the machine power. The
leads have to have a minimum cross-section of 1.5 mm2. If the mains cable is on a
reel, it has to be unrolled completely.
3. MOUNTING THE ACCESSORIES
Always remove the conntector before you carry out these actions!
Wait until the machine has come to a complete standstill and the milling cutter
has cooled down before you start replacing the cutters.
Mounting and removing the cutters
Fig. B
Use cutters with a shaft diameter which corresponds to that of the clamping chuck. Only
use cutters which are intended for the maximum speed of the machine. The diameter of
the milling cutter must not exceed the largest diameter (cf. chapter on “Technical data”).
Never press the spindle lock when the motor is running! The apparatus may
be damaged otherwise.
Press the button of the spindle lock (7), and turn the clamping chuck nut (6) until the
lock snaps in. Keep the spindle lock pressed during the following work steps.
Use the fork wrench to open the clamping chuck nuts (6) by turning it
counterclockwise.
Place the shaft of the milling cutter in the clamping chuck. The milling cutter shaft has
to be pushed in by at least 20 mm.
Tighten the clamping chuck nut (6) clockwise until the milling cutter has a tight fit.
In the delivery condition, a clamping chuck with an 8 mm diameter has been fitted in
the apparatus. For the use of milling cutters with a shaft diameter of 6 mm, the
clamping chuck can be replaced. For this purpose unscrew the clamping chuck nut
(6) anti-clockwise and pull the clamping chuck off the drive shaft. Place the 6 mm
clamping chuck on the shaft and use the clamping chuck nut (6) to tighten.
Setting the rip fence
Fig. A1, A2 & C
The rip fence is a practical tool for precise milling at a fixed spacing to the margin of the
workpiece.
Place the requested milling cutter in the apparatus.
Release the clamping lever (11), but keep it pressed.
Press the apparatus down until the milling cutter protrudes from the base plate (3),
and fasten the clamping lever (11) again.
GB
F
CZ
GB
Toledo 11
f. Tragen Sie geeignete Kleidung. Tragen Sie keine weite Kleidung oder Schmuck.
Halten Sie Haare, Kleidung und Handschuhe fern von sich bewegenden Teilen.
Lockere Kleidung, Schmuck oder lange Haare können von sich bewegenden Teilen
erfasst werden.
g. Verwenden Sie das Gerät immer mit geeigneten Staubabsaug- und
Auffangeinrichtungen. Das Verwenden dieser Einrichtungen verringert Gefährdungen
durch Staub.
h. Sichern Sie das Werkstück. Ein mit Spannvorrichtungen oder Schraubstock
festgehaltenes Werkstück ist sicherer gehalten als mit Ihrer Hand.
4) Sorgfältiger Umgang und Gebrauch von Elektrowerkzeugen
a. Überlasten Sie das Gerät nicht. Verwenden Sie für lhre Arbeit das dafür bestimmte
Elektrowerkzeug. Mit dem passenden Elektrowerkzeug arbeiten Sie besser und
sicherer im angegebenen Leistungsbereich.
b. Benutzen Sie kein Elektrowerkzeug, dessen Schalter defekt ist. Ein Elektrowerkzeug,
das sich nicht mehr ein- oder ausschalten lässt, ist gefährlich und muss repariert
werden. Beschädigte Schalter müssen in einer Kundendienstwerkstatt ersetzt werden.
c. Ziehen Sie den Netzstecker aus der Netzsteckdose, bevor Sie Geräteeinstellungen
vornehmen, Zubehörteile wechseln oder das Gerät weglegen. Diese
Vorsichtsmaßnahme verhindert den unbeabsichtigten Start des Geräts.
d. Bewahren Sie Elektrowerkzeuge außerhalb der Reichweite von Kindern auf. Lassen
Sie Personen das Gerät nicht benutzen, die mit diesem nicht vertraut sind oder diese
Anweisungen nicht gelesen haben. Elektrowerkzeuge sind gefährlich, wenn Sie von
unerfahrenen Personen benutzt werden.
e. Pflegen Sie das Gerät mit Sorgfalt. Kontrollieren Sie, ob bewegliche Geräteteile
einwandfrei funktionieren und nicht klemmen, ob Teile gebrochen oder so beschädigt
sind, dass die Funktion des Gerätes beeinträchtigt ist. Lassen Sie beschädigte Teile
vor dem Einsatz des Gerätes reparieren. Viele Unfälle haben ihre Ursache in schlecht
gewarteten Elektrowerkzeugen.
f. Halten Sie Schneidwerkzeuge scharf und sauber. Sorgfältig gepflegte
Schneidwerkzeuge mit scharfen Schneidkanten verklemmen sich weniger und sind
leichter zu führen.
g. Verwenden Sie Elektrowerkzeug, Zubehör, Einsatzwerkzeuge usw. entsprechend
diesen Anweisungen und so, wie es für diesen speziellen Gerätetyp vorgeschrieben
ist. Berücksichtigen Sie dabei die Arbeitsbedingungen und die auszuführende
Tätigkeit. Der Gebrauch von Elektrowerkzeugen für andere als die vorgesehenen
Anwendungen kann zu gefährlichen Situationen führen.
h. Elektrowerkzeuge nicht unbeaufsichtigt laufen lassen. Gerät immer ausschalten und
erst verlassen, wenn das Gerät völlig zum Stillstand gekommen ist.
i. Wenn die Anschlussleitung beschädigt wird, muss sie vom Hersteller oder seinem
Kundendienstvertreter ersetzt werden, um Gefährdungen zu vermeiden.
5) Service
a. Lassen Sie Ihr Elektrowerkzeug nur von einer qualifizierten Fachkraft unter
Verwendung von Originalersatzteilen reparieren. Dadurch wird die sichere
Funktionsweise des Elektrowerkzeuges gewährleistet.
D
F
CZ
GB
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toledo TBF-1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toledo TBF-1200 in the language / languages: English, German, French as an attachment in your email.

The manual is 3,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info