631461
21
Zoom out
Zoom in
Previous page
1/30
Next page
20
5. COMMON OPERATION (continued)
(2) PI SOUND/ PI MUTE:
PI SOUND mode: If a car is cruising between buildings, an oscillation phenomenon may occur, due to different
PI codes being received from the same AF.
PI MUTE mode: In above situation, the sound will be muted for less than 1 second.
(3) RETUNE L / RETUNE S:
The initial time of automatic TA search or PI SEARCH mode is selected.
When PI information is not received during retune time , the radio start to retune to next same PI station. When
same PI station is not received during 1 cyclic search, the radio goes to last station and waits for 4-5 minutes
until PI code is received.
RETUNE L mode: selected as 90 seconds./ RETUNE S mode: selected as 60 seconds.
(4) MASK DPI/MASK ALL:
MASK DPI mode: masked only the AF which has different PI.
MASK ALL mode: masked the AF which has different PI and NO RDS signal with high field strength.
(5) BEEP ON/BEEP OFF
BEEP ON mode: The beep is generated when any key is pressed.
BEEP OFF mode: The beep sound is disabled.
(6) VOL LAST/VOL DEFA
VOL LAST: The volume level when switching off will be restored with power ON.
VOL DEFA: The volume level of the main unit after power on is a constant value.
When selecting VOL DEFA item, press SEL button to display AVOL, then you can pre-set the constant volume
level after power on with VOL control.
(7) CLK ON/OFF
CLK ON: Clock will always show on the display when power is off.
CLK OFF: Clock will disappear from the display when power is off.
6. To display and adjust clock
Press CLK button briefly to display time for 5 seconds on the display, and then returns to its previous display
unless the button is pressed again.
Press CLK button and hold for more than 1 second until the real time flashes on LCD. Then you can adjust
HOUR or MINUTE with volume control.
7. To remove front control panel
Press RELEASE button to release front control panel from unit chassis, then you can remove it from unit chassis.
When the front control panel is removed, the LED indicator on front cabinet flashes.
8. To reset unit
Before operating the unit for the first time, after replacing the car battery or changing the connections, you must
reset the unit. To reset the unit, remove the front control panel, and then press RESET button with a sharp
object. This operation will erase clock setting and some stored contents.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tokai LAR-91B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tokai LAR-91B in the language / languages: English, French as an attachment in your email.

The manual is 1,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info