692130
11
Zoom out
Zoom in
Previous page
1/60
Next page
11
29. Front-mounted Stereo input 2 jack [ST 2 IN]
–10dB*,10kΩ,unbalancedtype,stereominijack.
It is internally connected in parallel to the Stereo
input 2. Adjust the input level with the Stereo 2
Input volume fader (28).
30. ARC switch and ARC operation indicator
[ARC] (Green)
Press this switch to enable the Automatic
Resonance Control function (ARC).
Hold down this switch for 3 seconds to start
the ARC measurement, and the ARC operation
indicatorashes.
Uponmeasurementcompletion,theARClteris
set, and the ARC indicator lights. (See p. 28.)
31. Recording output switch and Recording
output indicator [REC OUT] (Green)
The indicator lights when the switch is pressed,
and the Control knob (6) is allowed to adjust the
recording output volume. (See p. 25.)
* 0 dB = 0.775 V
[Rear terminal section]
32 33 34 35 36 3637
38 38
39 39
40
41
42 43 44
32. AC inlet
Connect this inlet to the AC wall outlet using the
supplied dedicated power cord.
33. Output terminals [OUTPUT 1 – 4]
+4dB*,600Ω,balancedtype,removableterminal
block.
The input channel signals assigned to Buses
1 through 4 using the Assignment switches (19
and 26) are output from each individual output
terminal.
Buses 1 through 4 correspond to the output
terminals 1 through 4, respectively.
34. Contact output terminals [OUTPUT C, 1, 2, 3,
4, 5, 6, 7, 8, C]
Removable terminal block, 8-channel contact
output terminal.
Perform function assignment to each contact by a
PC using the supplied M-864D PC Software.
35. Contact input terminals [INPUT C, 1, 2, 3, 4, 5,
6, 7, 8, C]
Removable terminal block, 8-channel contact
input terminals.
Perform function assignment to each contact by a
PC using the supplied M-864D PC Software.
36. AC adapter input [LINK A and LINK B]
Connect the dedicated AC adapter or its
equivalent* that supplies 24 V DC power to the
ZM Remote controller.
* Use the AD-246 AC adapter (optional) or its
equivalent. As for the usable adapter, consult
your TOA dealer.
37. Termination switch [TERMINATION ON, OFF]
UsedtoturnONorOFFtheterminationof120Ω
for parallel connection.
38. Data line connection terminals [D+, D–]
Connect the data line from the ZM Remote
controller to these terminals.
Match the polarity.
39. 24 V DC output terminals [DC 24 V, + and –]
Supply 24 V DC to the ZM Remote controller.
40. LAN port
Connect this port to the LAN-connected switching
hub using a LAN cable.
The MX-864D’s default IP address is “192.168.14.1.
Perform settings by a PC using the supplied
M-864D PC Software.
• Link indicator
Lights when the link is established and during
data transmission or reception.
• Full indicator
Lights during Full duplex operation.
41. Functional ground terminal
Connect this terminal to the functional ground of
external equipment if much noise is encountered
when the digital audio processor is connected
to the external equipment. The noise may be
reduced
Note: This ground is not for protective ground.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toa M-864D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toa M-864D in the language / languages: English as an attachment in your email.

The manual is 6,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info